Page 1 of 23 1234511 ... LastLast
Results 1 to 15 of 344

Thread: SRD - Ridox Single Turbo Project Build

  1. #1
    Nutrition Guru... Club Member Geo's Avatar
    Join Date
    May 2006
    Location
    Scotland - Strathclyde
    Posts
    10,525
    Feedback
    23 (100%)

    SRD - Ridox Single Turbo Project Build

    So the Car is with LeeP SRD (Supra Racing Developments) just now, and we have decided to go for a nice 650bhp car, i didnt want a car that was undriveable with loads of power, still enough power to keep 98% of cars at bay. So iv Spec'd up the car as it is just now, and will be adding the parts i buy and Lee installs at the Bottom. Lee will add pics when he gets round to it.

    The Car







    Engine Specifications:
    Toyota Stock Straight 6 Engine
    NGK Plugs BKR8EIX
    HKS 256/264 Cams
    Greddy Plenum
    Q45 Throttle Body
    Bosch 044 Fuel Pump
    Larger Lexus Oil Filter
    SRD FMIC
    Whifbitz Bonnet dampners
    Exhaust Manifold Gasket
    Inlet and Exhaust Cam Cover Gaskets
    Turbocharger & Induction:
    Precision T6765 .68(67mm turbo with .68 ar)
    50mm Turbosmart Waistgate
    Whifbitz Tubular Manifold
    Whifbitz 3'' Mid/Down pipe
    Turbosmart Raceport BOV
    Unorthadox Racing Pulleys
    Toyota OEM Engine Gasket Set
    Toyota OEM water pump
    Toyota OEM timing belt idler wheel
    Toyota OEM timing belt tensioner
    Toyota OEM crank shaft pulley
    Toyota OEM exhaust manifold nuts x12
    Toyota OEM Timing Belt
    Whifbitz Adjustable Cam Gears
    Fuel Lab 535 FPR
    SRD Billet Water Inlet Pipe
    TRD Thermostat
    SRD Heat shield
    Water output pipe Smoothed off and Polished
    4'' Polished Intake Pipe
    4'' K&N Filter
    Whifbitz Breather Tank
    Braided Oil Feed and Return Lines
    50mm BOV

    Fuel, Tuning & ECU:
    Syvecs ECU with Trac Control
    3.5 Bar AEM Map Sensor
    Power Enterprise 800cc Injectors
    Injector seals
    Stock Fuel Rail
    Stock Fuel Filter
    AEM wideband
    Fuel Pulsation Dampner
    1/8 NPT straight fitting

    Cooling:
    SRD 4'' FMIC with Custom Piping
    Koyo Radiator
    Supra FMIC and Rad Cooling plate
    AAP Motorsports Dual Fan Kit with Shroud
    Heat Wrapped Down/Mid Pipe
    HKS Oil Cooler
    Blitz 1.4bar Rad Cap
    Power Steering Cooler

    Exhaust:
    Supra Dragger 4'' Exhaust
    Envy Decats

    Drivetrain:
    6 Speed Manual Getrag Gearbox
    Whifbitz Solid Gearshift Bushes
    Toyota Gear Selector Seal
    Stock LSD
    Whifbitz Solid Selector Bushes
    Southbend DXD-F Series Clutch
    clutch cover washer

    Suspension, Wheels, Tires & Brakes:
    UK Spec Brakes all Round 4/2 Pot(Front and Rear)
    OEM Disks, Chris Wilson Fast Road Pads
    Do Luck Braided Brake Lines
    Wed SA-70 Wheels 9x18 and 10x18 +32 offset
    Race Wheel Nuts
    Falken 452 Tyres all Round
    Tein Coilovers and Adjustable Suspension
    Cusco Front and Rear Strut Braces

    Interior & ICE:
    JVC KW-AVX740
    Alpine front and rear speakers
    Defi Control Unit, Water Temp, Boost, Oil Temp
    DC2 Recaro Bucket Seats, with MO BRIDE rails
    Carbon Fiber Gauge Holder

    Exterior:
    Full Genuine Ridox Body Kit.
    UK Bonnet Scoop
    De Wipered
    De Ariel
    UK Glass Headlights
    6000k Knight Racer HID's


    Performance:
    Max power - 712 bhp
    Max torque - 659 ftlbs
    Fly - 605rwp
    Attached Thumbnails Attached Thumbnails After1.jpg   after2.jpg   pulleys.jpg   OEM parts.jpg  
    Last edited by Geo; 23-12-11 at 20:42.
    My Old Car
    mutantgeneticnutrition@gmail.com

    My YouTube Page

    Xbox Gamer Tag scottish sarge

  2. #2
    Me? Post? Never! Club Member Ryan.G's Avatar
    Join Date
    Feb 2007
    Location
    England - Oxfordshire
    Posts
    3,768
    Feedback
    49 (100%)
    Have you brought the RLTC Mate?

    If not dont bother and use the money from the RLTC aswell as selling the aem, and dli and just get a syvecs fitted mate which has traction control built in plus all the other major selling points which are all over this forum.

    Ryan

  3. #3
    Nutrition Guru... Club Member Geo's Avatar
    Join Date
    May 2006
    Location
    Scotland - Strathclyde
    Posts
    10,525
    Feedback
    23 (100%)
    Quote Originally Posted by Ryan.G View Post
    Have you brought the RLTC Mate?

    If not dont bother and use the money from the RLTC aswell as selling the aem, and dli and just get a syvecs fitted mate which has traction control built in plus all the other major selling points which are all over this forum.

    Ryan
    Its with Lee just now bud, so id have the RLTC, AEM, DLI. Pm a price for the Syvecs along with it mapped bud. Wont be picking her up till next year at some point so im not sure which route i'll go with regarding the ECU, all depends on cash.
    My Old Car
    mutantgeneticnutrition@gmail.com

    My YouTube Page

    Xbox Gamer Tag scottish sarge

  4. #4
    Me? Post? Never! Club Member Ryan.G's Avatar
    Join Date
    Feb 2007
    Location
    England - Oxfordshire
    Posts
    3,768
    Feedback
    49 (100%)
    Prices up to Jan 2011

    Syvecs S6 - 1530
    Loom - 130
    Traction Install and Setup - 75
    Mapping on the dyno - 350

  5. #5
    Nutrition Guru... Club Member Geo's Avatar
    Join Date
    May 2006
    Location
    Scotland - Strathclyde
    Posts
    10,525
    Feedback
    23 (100%)
    Lee just sent me a text. He did a compression test

    Results

    1:198
    2:197
    3:198
    4:199
    5:197
    6:198

    So we can say the Engine is in good condition with good numbers all round

    pic of Bay Below before Lee Starts
    Attached Thumbnails Attached Thumbnails photo.jpg  
    My Old Car
    mutantgeneticnutrition@gmail.com

    My YouTube Page

    Xbox Gamer Tag scottish sarge

  6. #6
    Nutrition Guru... Club Member Geo's Avatar
    Join Date
    May 2006
    Location
    Scotland - Strathclyde
    Posts
    10,525
    Feedback
    23 (100%)
    Right,

    So iv decided to go with the syvecs ECU now, Ryan is sorting that out for me. So Lee is ripping the AEM ECU, HKS DLI out. Ryan said to keep the AEM 3.5 Bar sensor as it will work perfectly fine. So the AEM and DLI is up for grabs.

    Spoke with Lee today, and were now relocating stuff about a bit to tidy up the Gauges in the car, and the Engine bay. The Defi Controller will be in the Stock drawer below the Stereo, and were moving the boost gauge from the Air Vent to the Carbon fibre holder.

    trying to figure out what else i need to do when its with Lee, any help will be appreciated

    cheers
    My Old Car
    mutantgeneticnutrition@gmail.com

    My YouTube Page

    Xbox Gamer Tag scottish sarge

  7. #7
    Nutrition Guru... Club Member Geo's Avatar
    Join Date
    May 2006
    Location
    Scotland - Strathclyde
    Posts
    10,525
    Feedback
    23 (100%)
    Bay Partially Stripped, turbo side still to come off.

    Stock Cams Removed

    HKS 256/264 Cams to be Installed

    Some Surface Rust, Lee polished them up

    Runners Stripped down and parts removed thats not needed

    All Cleaned up and ready to go back on

    HKS cams installed and clearances checked all ok.

    New Front Main Seal installed
    Attached Thumbnails Attached Thumbnails 2.jpg   1.jpg   3.jpg   4.jpg   5.jpg  

    6.jpg   7.jpg   8.jpg  
    Last edited by Geo; 02-02-11 at 15:53.
    My Old Car
    mutantgeneticnutrition@gmail.com

    My YouTube Page

    Xbox Gamer Tag scottish sarge

  8. #8
    Nutrition Guru... Club Member Geo's Avatar
    Join Date
    May 2006
    Location
    Scotland - Strathclyde
    Posts
    10,525
    Feedback
    23 (100%)
    Parts that were stripped under the Inake runners, that aint needed.
    Attached Thumbnails Attached Thumbnails 9.jpg  
    Last edited by Geo; 02-02-11 at 15:54.
    My Old Car
    mutantgeneticnutrition@gmail.com

    My YouTube Page

    Xbox Gamer Tag scottish sarge

  9. #9
    Nutrition Guru... Club Member Geo's Avatar
    Join Date
    May 2006
    Location
    Scotland - Strathclyde
    Posts
    10,525
    Feedback
    23 (100%)
    Little Update -

    Iv SORN'd the car today as no point wasting tax, plus it needs and MOT also.

    Also just off the phone to Paul, and ordered up Fuel Lab fpr with gauge and fitting kit, and a Turbosmart Race port Bov.

    All i need now is rear tyres, and some new plugs.
    My Old Car
    mutantgeneticnutrition@gmail.com

    My YouTube Page

    Xbox Gamer Tag scottish sarge

  10. #10
    I'm part of the furniture Club Member Paul Whiffin's Avatar
    Join Date
    May 2001
    Location
    Wales - Gwent
    Posts
    16,338
    Feedback
    241 (100%)
    Quote Originally Posted by Geo View Post
    Little Update -

    Iv SORN'd the car today as no point wasting tax, plus it needs and MOT also.

    Also just off the phone to Paul, and ordered up Fuel Lab fpr with gauge and fitting kit, and a Turbosmart Race port Bov.

    All i need now is rear tyres, and some new plugs.
    I've got NGK's on special offer at the moment mate....
    The UK's Premier Supra Specialist with 18 years of Supra tuning. Servicing,Tuning,Fast Road/Track Day/Race Car Build/Prep.We hold the largest stock of Supra parts in the UK with our own range of performance parts.
    2009 Time Attack Club Class RWD Champions - 2010 Time Attack Club Pro RWD Runners Up, builders of the fastest Supra's in the UK
    www.garagewhifbitz.co.uk
    sales@garagewhifbitz.co.uk
    Special Offer Section - New Products Section - Garage Whifbitz Youtube Channel - Garage Whifbitz Facebook Fan Page - Follow Us on Twitter

  11. #11
    Nutrition Guru... Club Member Geo's Avatar
    Join Date
    May 2006
    Location
    Scotland - Strathclyde
    Posts
    10,525
    Feedback
    23 (100%)
    when does the offer Expire bud?
    My Old Car
    mutantgeneticnutrition@gmail.com

    My YouTube Page

    Xbox Gamer Tag scottish sarge

  12. #12
    I'm part of the furniture Club Member Paul Whiffin's Avatar
    Join Date
    May 2001
    Location
    Wales - Gwent
    Posts
    16,338
    Feedback
    241 (100%)
    Quote Originally Posted by Geo View Post
    when does the offer Expire bud?
    25th Feb
    The UK's Premier Supra Specialist with 18 years of Supra tuning. Servicing,Tuning,Fast Road/Track Day/Race Car Build/Prep.We hold the largest stock of Supra parts in the UK with our own range of performance parts.
    2009 Time Attack Club Class RWD Champions - 2010 Time Attack Club Pro RWD Runners Up, builders of the fastest Supra's in the UK
    www.garagewhifbitz.co.uk
    sales@garagewhifbitz.co.uk
    Special Offer Section - New Products Section - Garage Whifbitz Youtube Channel - Garage Whifbitz Facebook Fan Page - Follow Us on Twitter

  13. #13
    Nutrition Guru... Club Member Geo's Avatar
    Join Date
    May 2006
    Location
    Scotland - Strathclyde
    Posts
    10,525
    Feedback
    23 (100%)
    Quote Originally Posted by Paul Whiffin View Post
    25th Feb
    ah cool got plenty of time then.

    cheers
    My Old Car
    mutantgeneticnutrition@gmail.com

    My YouTube Page

    Xbox Gamer Tag scottish sarge

  14. #14
    Admin Super Moderator Steve's Avatar
    Join Date
    Jul 2004
    Location
    (Top Secret)
    Posts
    14,012
    Feedback
    59 (100%)
    Geo, can you please upload all your photos to the forum rather than linking from Photobucket.

    Thanks
    Steve

  15. #15
    Nutrition Guru... Club Member Geo's Avatar
    Join Date
    May 2006
    Location
    Scotland - Strathclyde
    Posts
    10,525
    Feedback
    23 (100%)
    Quote Originally Posted by Steve View Post
    Geo, can you please upload all your photos to the forum rather than linking from Photobucket.

    Thanks
    Steve
    ok dokey, will change it later on tonight. just heading out to gym
    My Old Car
    mutantgeneticnutrition@gmail.com

    My YouTube Page

    Xbox Gamer Tag scottish sarge

Page 1 of 23 1234511 ... LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •