jza800

hmm there is no relay, dont you mean the fuel pump ecu??

I have now looked, i can not find Any relay in the back of the car, where do I find it??

did fix the running issue, so now the engine run as it should. so only problem i have now is power to the fuel pump.. i can start the car when bridge FB and B+ on the diagnostic terminal.. but as soon as i take the bridge out, it can not start, so i have to have a wirring problem.. but where to search ??

I have a starting issue on my supra, i have had the engine out, due bodywork, after i have put the engine in the car again, it won't start.. have changed the timingbelt, (have checked timing and it is spoton, have checked timing mark on engine 2 on the top and crankshaft) and i have changed the o rings on the injectors. if i bridge fb + b+ on the diagnostic terminal the engine starts up, but don't run on all 6 cylinders, and if i give it a little throttle the engine stalls/engine cut out. bt if i give a little throttle at the time, it don't stalls but it still not going on all 6 cylinders.. so i will mean that the fuel pump and fuel pump ecu and wire have to be ok. i have the interiør out of the car, so have not checked the engine codes.. Have i missed something, and what could my problem be, the engine did run fine before i got it out of the car?

Yes it requires knowledge and patience, and not everyone has it unfortunately, have seen some users in here also have to try it for themselves, it has not gone through so well

Yes they have the other too, there are 2 styles. you have found style 1 i have style 2 https://www.ebay.co.uk/itm/WHITE-STITCH-2X-FULL-DOOR-CARD-LEATHER-COVER-FOR-TOYOTA-SUPRA-MK4-93-02-STYLE-2/352007667204?hash=item51f54abe04:g:zwcAAOSwSlBYy~5g

I dont know the price you have in england about upholsterer, but here they are expensive, what one door card would cost if they had to make it all with mounting leather and work, with j f customs i could get it all for what one side would cost...

no i did not remove the vinyl the covers it made to fit over the stock vinyl, if you take it off you will have a big problem to get et all smooth and even.. i used some heat resistent glue so the leather not will slip the vinyl when it get hot outside.. normal spray glue will slip if the car says in the hot sun..

afraid not...

Yes i am doing the dash, and the arm rest and the rear door cards next time.. will trye so see how it does when the summer kicks in.. but it seems like a really good kvalitet

I payed £204 + shipping for both door cards..

I Will give more details when i go home i am at work. I bourght the cover online and mountet Them myself it is not a job for a rookie the fitment was really good. If you need more information dont hassitate to ask

I finally got around to fit leather on my door cards really satified with the result

thanks for answer, looks like the ones on ebay are same same as other places as long they are steel ones

Hi I have got some custom made wheels to my widebody supra, but need some new nuts to them, i have search the forum, and many say go for steel ones instead of aluminium ones, the holes in the rim is very tight, so i need to find some that do not filling much in the hole. so i have look on this ones, what are people's opinion about those ones? https://www.ebay.co.uk/itm/Blue-Tuner-Wheel-Nuts-x-20-12x1-5-for-Toyota-Corolla-Starlet-Celica-Supra-Rav4/273040897113?hash=item3f92817459:g:yvQAAOSwtKVaT6pY

Check your wirring loom on the transmission, if it was an auto before, you have to find the plug, it is not used on the manual transmission, so it is hanging around the left side of the transmission, then you have to find the pins to the park position sensor in the plug as it was an auto it has to be in park to start.. you have to bridge those 2 to make it start now.

Hi I have bought a new A/C kompressor as the old one was leaking.. When i mount the new kompressor, do i have to pre-oil it, or will it automatik do that when i go to a shop to fill the A/C system up. I have bought this one : https://www.rockauto.com/en/moreinfo.php?pk=2022976&cc=1278604&jsn=900&_nck=8lwjyqYeLE0kuAoyLmPTRw40tfIODn2HvMMFF2jg6FvNOYYQ0Y9TQ%2FtPwj%2BjDLvD5hIR5L2gVzmng8titdIAlvcUEs54nzLHEp%2F1REjtckBgLFndgly2eZkrPM9%2BJ8Ja2Tw9PiMwDZ7rCtNDdz%2F9%2BzcnyPBd4EYuiKObu5CuvnIVCXK1m80JGNsFOEYIGXWN7nDL7qf3Ij4RDKkjrZ8mftEKf2ZCKbCRIH3WvDeVvLFaNGH1UMTuhwIHhtlEhp0gLZWVXQnI2Ug1v9JUe0W3qa4R1zJKa3gRy6yd4J2TRCDi2qW6umIuIM545beGYf48jDC2AWfpDg5Y%2BXidztLEhvU9y0CES0xPYDatlTJtDY8%3D

toyota dont have them, they say it is possible a new lock set or door handle... and that sounds a little overkill for that.

hi I am in a need of that black gasket there are where the red arrow points. someone know where it is possible to get?

Hi I am building a show and shine engine to my widebody supra. many engineparts are paintet, have thought about painting the stock fuel rail, but i am afraid it wont hold up. So what possibility do i have when it comes to the stock fuel rail, is it possible to get a fuel rail and other injector or is it possible to find a fuel rail where the stock injectores fits in to? it have to run in the stock ecu. i am not after more power, just not like the stock fuel rail.

bump

Hi I have bought some door covers to my supra mkiv, it is some covers that you glue on the old covers, have some in here tried to mount them on their own supra, and can give some how to guide? do you remove the old leather or what is it called on the door boards or do you glue it over the stock leather on the cards?? i have bought those. https://www.ebay.co.uk/itm/PURPLE-STITCH-2X-FULL-DOOR-CARD-LEATHER-SKIN-COVER-FITS-TOYOTA-SUPRA-MK4-93-02/351096910442?_trkparms=aid=111001&algo=REC.SEED&ao=1&asc=20160908105057&meid=add245a68f574bd5958baf285bcb16ab&pid=100675&rk=11&rkt=15&sd=264543667341&itm=351096910442&pmt=0&noa=1&pg=2380057&_trksid=p2380057.c100675.m4236&_trkparms=pageci:e785e6c4-0ed0-11ea-b3e7-74dbd1803353|parentrq:9e135a7516e0a4e922668956ffe69bbe|iid:1

hehe only -8 in offset. mine is 13x19 offset -20