Glosphil

Welcome aboard

Depends how good they are lol

Welcome, good luck finding your supra

Have you looked at overscan/underscan in the driver control panel? I have the same issue and use that on my Nvidia and ATI Cards. Solved it no probs on my 50" Plasma.

Cheers Ash, see you Saturday. Does anyone wanna buy my soul? I'm selling it cheap haha

Just to respond to these both together. Ash is correct and informed me I needed one and might I say he's been great. We had an issue with the parts company delivering the wrong clutch, which left me stranded, Ash drove me all the way home. Great bloke and has gone out of his way for me. This post is no way intended to say otherwise, just looking at options before I call my bank manager haha.

Ok, got a mixture of opinions here. Ash, how bad is the judder, do you think it will bed in like bignums did? If not, can you order and fit before I get back? I'll call you in a bit.

Hi Guys, just had a new clutch fitted to my 6 speed, and the garage inform me there is now juddering and I will need a new flywheel. I need a bit of advice really, I saw the flywheel when the gearbox was off and it had a couple of burn marks on it, but nothing more than a few microns I'd guess, will it smooth out after a bit with the new clutch? I had no judder at all with the old one. its a touch less than 500 for a new flywheel aparently, is there another option? resurfacing or a cheaper place than MR T? The clutch itself is all on the credit card, so could do without the flywheel too as I'm skint. Will driving it ruin the new clutch? Cheers for your advice Phil

Excellent, Can you quite me happy for a suitable clutch for BPU 6 speed twin turbo? Thanks

My clutch is slipping badly on my Jspec TT BPU. Does anyone know a place near to Nottingham/Loughborough I can get a new one supplied and fitted? I heard a new standard one is fine for BPU? or is there a better option? Thanks

Thanks, what did you replace it with?

How do you adjust the clutch?

I think my clutch is slipping, but just thought I'd check with you guys. I've tried pulling off with the hand brake engaged and no rev climb. I've tried a high gear and revving and no rev climb... until i reach full boost. When I'm driving in higher gears, when I come on boost the rev shoots up 1 about 1-2k then dropped back down and pulls away. I presume its clutch slip, its been doing it 2 weeks now, how long is it likely to last? what will happen when it goes? Any recommendations for a replacement for BPU? and where to get fitted in notts area? Thanks guys

Bummer just seen this, I would of had that for more than it sold lol

Hi, my Supe failed its MOT today because the fog light is not working. On taking the panels out to find out why, I notice it is connected to the wire going into the switch for the parking sensors. Neither the parking sensors or the fog light are working. I've been through the fuse box but cant find any blow. Do you know where the fuse is? need it re-tested in the morning. Many thanks Phil

My clutch is creaking a bit and I've oiled the pedal etc so its not that. I read I can spray some WD40 in the inspection plate and it should cure it. Only thing is, where is the inspection plate? couldnt see anything under the gearbox, but then never seen one before, could someone describe where it is? Thanks

You can buy new internals for them easy enough from Toyota, I bought a set of master and slave ones and did the lot, easy job.

Not very nice mate, if I were you I'd let me take them off your hands so you dont get too much grief over them. I'm glad to help.

I bought 3 of the bolts for the manifold where the 1st cat goes because my decatt pipe was gassing and I couldnt do them up anymore. I've removed 2, but the lower one is now rounded off at the tip and on the nut and I cant turn it. I've had a look at taking the manifold bit off, and removed the bracket and the air sensor but the 3 (are there 3) nuts I can see I cant get to because the decatt pipe is still on. anyone got any good ideas? I've been at it hours and I'm totally stuck Cheers

128k up, 5meg down forget what you have to download to hit it, its on their website somewhere.

Yeah I know, I have 3 machines online at the same time as that too. I've had 20 before. Best service I've had. I did hit their fair use cap the other day though, speed down to 25% of capacity for 5 hours, annoying lol

File size transferred : 10.0 MB (10485760 bytes) Total time taken : 4.45 seconds (4453 milliseconds) Throughput : 2354.0 KB/sec [Kilobyte-per-second] = 2.35 MB/sec [Megabyte-per-second] = 18832.0 Kbps [Kilobit-per-second] = 18.83 Mbps [Megabit-per-second]

I'm getting worried, big 6ft bloke smiling at all the men. lol

Is that because you've gone soft? lol

Do you change the filter and the oil or just the oil? I always change the oil and filter roughly around 8k. wonder if just change the oil every 5 and the filter every 10 would be reasonable? Also wondering if I should be changing it myself as I dont get a magic stamp if I ever want to sell it on (only reason I would would be to buy a newer one)