Sharpie

Hi Chris, they both work just fine it's just something I noticed while swapping them around during testing.

Thanks Gents

Hi, I'm just about to replace the hose from the power steering reservoir to the pump, since my old one needed to be replaced. Does anyone have any tricks or tips ? Once the pipe is on and I have filled up the reservoir, I assume I can leave the cap of the reservoir off while the engine runs so, I can turn the wheels from side to side to get the air out ? or will fluid go everywhere ? Any other advice ? Cheers Pete Oh, I have already read this. http://web.archive.org/web/20041209173121/www.reepa.com/psflush.php

Both units are from 95 UK spec cars but, one is Auto the other Manual. Why the different numbers before the airflow direction arrow ? 1 = Manual 2 = Auto Part numbers are the same. Bar codes are different. 1 = 502210129552 2 = 502210129804

I have in the past need to look at photo's of a UK spec MAF off the car but, they seem to be a little hard to find so, while I had mine off, I took a few pic's. This will show how they are different to the Jspec 98on MAF's. Maybe they could be added to the FAQ/Guide section ? Part Number 22250-46030 RRP £619:52 inc. VAT. The arrow on the bottom of the MAF indicates the airflow direction but, if you use the bolt holes to install on the piping bracket, then it can only be fitted one way.

WOW, a supra that is actually finished!!! Well, almost All the best Ian, your "I see you have taken steps to cover " joke about my engine photo will always put a smile on my face Another legend steps down....

My situation was different, by the time I fitted it, and the car had cooled down, the pipe was empty since, it has leaked everywhere I have to say that the way the Toyota clips are pre-extended (kept open with a small metal red clip) was great, easy to slide on and then just ping off the small red clip holding the hose clip open and then then it snaps right in place. I guess you could use a small container to catch any fluid loss as you take the old one off and would guess an

No problem.

Rad Hose T16571-46150 Mr T's price is £11.15 + Vat Rad Clips x 2 T90467-37005 Mr T's price is £4.55 + Vat each. £23.79 all in. VERY easy to fit = no tools. I just had to loan a screw driver to take the other pipe off.

Nice looking RSP soop, flashed and waved :-)

This morning......I flashed but, no reply :-(

I wonder if Cuba takes his soop

http://www.spiderlite.jp/WanganSpiderliteImpreza2.jpg Along the same lines as the lambo really. http://www.bcopping.com/reventon/post-7346-1210447795_thumb.jpg

Welcome to the club, what have you done to your car ? any photo's ? Give this a try first http://www.mkivsupra.net/vbb/showthread.php?t=145249&highlight=IAC 10 min job.

Very nice to see that Sir Matt is still around to see this again RIP '58

Not in the 1st half

Sharpie (pissing coolant everywhere, but, I'll be there) I have to drive past the meet to get to the hotel so, it's on my way. If anyone can help tonight ? http://www.mkivsupra.net/vbb/showthread.php?t=151062

Thanks for the offer Chris, I have purchased 5ltrs of 4life which, added to the 2-3ltrs that I brought with me, should see me through until tomorrow with this level of leakage. I was hoping that someone locally might be able to help me out for tonight. The Toyota garage will have a new stock hose and clips for me by 10am tomorrow.

a couple of photo's of the split in the other end of the hose that is not leaking yet. There area where it is leaking is at the water neck hose. Does anyone know how much coolant the alternator can take before packing up ?

I'm visiting Bracknell and will be attending the Reading meet tonight but, on the way down to Bracknell this morning, I have just found that one of the silicone hoses on the polished rad pipe is split and is pissing coolant everywhere. Does anyone going to the Reading meet have a spare top rad pipe hose just need one end of the hose,[sHOCK][/sHOCK] that I could loan from them ? I have toyota bringing me in a new stock pipe and clips for tomorrow but, would like to get it fixed up tonight if I can. Edit - If you could bring some tools too ? I guess that would help too......sorry to ask...

Thanks for the nice comments Rob I keep meaning to join the local meets but, work has been crazy this year. No leaks after visiting Mr Wilson yesterday (Sunday call out !!!)

Just out for an installation lap (M6) and checking for leaks I did not see you

Cheers buddy, I have just PM'd Kev so, should be OK. Thanks again for offering

Did I really do that

Great! so, it's a known good one ? It is the UK spec one right ? and not the VVTI MAF as they are different