TT-DEK Posted July 23, 2007 Share Posted July 23, 2007 HI, can anyone help? Where do these fit? Link to comment Share on other sites More sharing options...
danny_silva Posted July 23, 2007 Share Posted July 23, 2007 in the edge of the pads.... theres 2 little holes.. 2 on each side!! So it will be 2 on top and 2 on the bottom.. it goes from one pad to the other side!! I hope you understand!! Link to comment Share on other sites More sharing options...
danny_silva Posted July 23, 2007 Share Posted July 23, 2007 take that part were you got the supra logo and you can see the holes... lol.. Link to comment Share on other sites More sharing options...
TT-DEK Posted July 23, 2007 Author Share Posted July 23, 2007 Oh dear, these are assembled. Do i have to take apart again, or will these squeeze in? and thanks... Link to comment Share on other sites More sharing options...
Tom S Posted July 23, 2007 Share Posted July 23, 2007 Derek, pm me your address or bank details need to send you that £40+ from JAE Link to comment Share on other sites More sharing options...
Scooter Posted July 23, 2007 Share Posted July 23, 2007 Oh dear, these are assembled. Do i have to take apart again... yes but its a piece of p*ss..........at the top and bottom of the caliper on the inside are x2 14mm bolts. Loosen the bottom one til finger tight and undo and remove the top one completely. Then from the top prise the central part that covers the pads, up and away from the wheel and towards the rear of the car (it will pivot on the finger tight, but still in place bolt) This will expose the pads and the holes these bits/springs fit into. Pop them in and push the caliper back, slot the bolt back in and tighten both bolts back up, job done............. Link to comment Share on other sites More sharing options...
TT-DEK Posted July 23, 2007 Author Share Posted July 23, 2007 yes but its a piece of p*ss..........at the top and bottom of the caliper on the inside are x2 14mm bolts. Loosen the bottom one til finger tight and undo and remove the top one completely. Then from the top prise the central part that covers the pads, up and away from the wheel and towards the rear of the car (it will pivot on the finger tight, but still in place bolt) This will expose the pads and the holes these bits/springs fit into. Pop them in and push the caliper back, slot the bolt back in and tighten both bolts back up, job done............. Sounds all too easy:rolleyes: Thanks buddy, will have a go tomorrow:cool: Link to comment Share on other sites More sharing options...
TT-DEK Posted July 23, 2007 Author Share Posted July 23, 2007 Derek, pm me your address or bank details need to send you that £40+ from JAE TOM:innocent: You already paid me buddy;) But if your giving i don,t mind takin:p Yeh, you gave it me back out of your own money Tom. You must av had a couple too many:d:d Link to comment Share on other sites More sharing options...
Tom S Posted July 23, 2007 Share Posted July 23, 2007 You must av had a couple too many:d:d so tired mate just wasn't sure. Thanks for the honesty Link to comment Share on other sites More sharing options...
TT-DEK Posted July 23, 2007 Author Share Posted July 23, 2007 so tired mate just wasn't sure. Thanks for the honesty No probs buddy, must admit, there was money flyin round everywhere that day Tom,with all the shopping and stuff I,m suprised you kept track fella? I,d av been £400 out of pocket me:search: Link to comment Share on other sites More sharing options...
Tom S Posted July 23, 2007 Share Posted July 23, 2007 still not done a final cash book yet. will post costs tomorrow Link to comment Share on other sites More sharing options...
TT-DEK Posted July 23, 2007 Author Share Posted July 23, 2007 If theres a penny over Tom, you keep it mate, treat your self for all the hard work you put in. JAE would not of been a success without your efforts, thanks again Tom, i think i can speak for all concerned, Link to comment Share on other sites More sharing options...
Pixelfill Posted July 23, 2007 Share Posted July 23, 2007 If theres a penny over Tom, you keep it mate, treat your self for all the hard work you put in. JAE would not of been a success without your efforts, thanks again Tom, i think i can speak for all concerned, Link to comment Share on other sites More sharing options...
Pixelfill Posted July 23, 2007 Share Posted July 23, 2007 Does this help ? Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now