Dnk Posted April 1, 2016 Share Posted April 1, 2016 Started refurbing these wheels yesterday Link to comment Share on other sites More sharing options...
Sheefa Posted April 1, 2016 Share Posted April 1, 2016 Like them a lot Dunk. Colour change or staying silver? Link to comment Share on other sites More sharing options...
Tsia Posted April 1, 2016 Share Posted April 1, 2016 I was going to give this a shot on my wheels this weekend - I'll be disappointed if my results don't look that tidy now Nice work Link to comment Share on other sites More sharing options...
Dnk Posted April 1, 2016 Author Share Posted April 1, 2016 Like them a lot Dunk. Colour change or staying silver? Not sure any other colours would work that well, gloss Black perhaps They're going on my 330 so I think the same colour or maybe a lighter silver perhaps. Link to comment Share on other sites More sharing options...
Dnk Posted April 1, 2016 Author Share Posted April 1, 2016 I was going to give this a shot on my wheels this weekend - I'll be disappointed if my results don't look that tidy now Nice work Thanks but i'm not finished yet Link to comment Share on other sites More sharing options...
Tsia Posted April 1, 2016 Share Posted April 1, 2016 I meant more about how smooth the repaired edge looks Link to comment Share on other sites More sharing options...
Dnk Posted April 1, 2016 Author Share Posted April 1, 2016 I have a die grinder and use Roloc sanding discs on the lips and then finish by hand Link to comment Share on other sites More sharing options...
Glanza_Mike Posted April 1, 2016 Share Posted April 1, 2016 Do you use some sort of filler or something to fill in areas that are a bit deep mate or not? Or just sand them right back? Link to comment Share on other sites More sharing options...
Dnk Posted April 1, 2016 Author Share Posted April 1, 2016 I get them welded if its bad enough, I have a mate just down the road from me who does this if required, these weren't that bad and I've just dressed them back I guess you could use body filler or similar but personally i'd rather weld them if required, not sure how filler would like 200 c in the oven if you were powder coating them though ! Or if it would cope with tyre fitting/removal Link to comment Share on other sites More sharing options...
Tsia Posted April 1, 2016 Share Posted April 1, 2016 I've already purchased some chemical metal as it reads like it'll do the job - and I might have to purchase a grinder at the weekend as they're only £30 or so from B&Q Link to comment Share on other sites More sharing options...
Dnk Posted April 1, 2016 Author Share Posted April 1, 2016 I've already purchased some chemical metal as it reads like it'll do the job - and I might have to purchase a grinder at the weekend as they're only £30 or so from B&Q I guess it really depends on how large an area your trying to fill and is it on the edge of the lip, it might pay you to do the repair then test it to see how strong it is before continuing with the refurb. Filler would I think just break off with not a great amount of force if on a lip hence I don't use it Link to comment Share on other sites More sharing options...
Dnk Posted April 2, 2016 Author Share Posted April 2, 2016 Finished off the lips today, 180 grit first then 320 grit Link to comment Share on other sites More sharing options...
Kev.O Posted April 2, 2016 Share Posted April 2, 2016 Looking nice Dunk. Link to comment Share on other sites More sharing options...
Glanza_Mike Posted April 2, 2016 Share Posted April 2, 2016 Good work mate. Link to comment Share on other sites More sharing options...
Dnk Posted April 2, 2016 Author Share Posted April 2, 2016 Thanks guys Link to comment Share on other sites More sharing options...
Dnk Posted April 4, 2016 Author Share Posted April 4, 2016 Before they get finished 'm going to swap the tyres over from the 18's that are on the car and see if i have any rubbing issues. Doing that at 14:00hrs today so fingers crossed Link to comment Share on other sites More sharing options...
Dnk Posted April 4, 2016 Author Share Posted April 4, 2016 Did the tyre swap off the old wheels so I could see if I had any rubbing issues, took it for a test drive and all's good Ordered new rear tyres so just need to crack on and finish them now Link to comment Share on other sites More sharing options...
Kev.O Posted April 4, 2016 Share Posted April 4, 2016 They look great Dunk, lovely fit. Link to comment Share on other sites More sharing options...
Dnk Posted April 5, 2016 Author Share Posted April 5, 2016 They look great Dunk, lovely fit. Cheers Kev, way better than the OE fitment and no rubbing Link to comment Share on other sites More sharing options...
Dnk Posted May 6, 2016 Author Share Posted May 6, 2016 Perfect weather for a rag top Link to comment Share on other sites More sharing options...
mplavery Posted May 6, 2016 Share Posted May 6, 2016 I would get the new tyres on before you paint them mate, If I knew it was having a tyre I would want that on first just in case anything happens while the new tyre was getting fitted on fresh paint. Just have the rim popped though as you have a BMW im guessing you have run flats so might be hard to have the rim popped all the way round lol Link to comment Share on other sites More sharing options...
Dnk Posted May 6, 2016 Author Share Posted May 6, 2016 The wheels are finished and no problems getting the tyres on and off I don't use run flats, horrid things !! The only problem I have is the replacement centre caps I bought from Racing Dynamics don't fit as they appear to be different to the two that came with the wheels, I emailed them 5 days ago no response and 2 days ago no response, not impressed now Link to comment Share on other sites More sharing options...
Dnk Posted May 7, 2016 Author Share Posted May 7, 2016 Got the centre caps to fit by heating them up in boiling water to make the location pegs a bit more flexible, they still took a lot of force to get them in the wheel. Should be interesting getting them out when the tyres need changing ! Finally got a reply from RD and they put it down to a change in manufacturing and there's not a lot they can do about it other than I send them back and get a refund. At least they replied but i'm happy now they fit so end of drama Link to comment Share on other sites More sharing options...
Hitbox Junkie Posted May 7, 2016 Share Posted May 7, 2016 Awesome!! Look great think keeping them the same colour will suit the car. Inless your going for the murdered out look Link to comment Share on other sites More sharing options...
Dnk Posted May 7, 2016 Author Share Posted May 7, 2016 Awesome!! Look great think keeping them the same colour will suit the car. Inless your going for the murdered out look Thanks I did think about gloss Black or shadow chrome but will stick with them how they are for now I shall be selling the OE wheels now as I'm happy how these have turned out Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now