jamesmark Posted July 5, 2008 Share Posted July 5, 2008 My UK spec S14a cannot change gear it only started this. No warnings etc and car ran fine up until the point where I went from 4th to 5th and I could not engage 5th. Now when the engine is running I cannot engage any gear. When the car is off I can select all gears. I drove the car for 1 mile in 2nd (as was on my way home from work) and when I depress the clutch nothing happens, the car remains in gear and the revs do not climb. The clutch pedal feels ok maybe a little light but I don'tknow if that's just my imagination. Any ideas guys? I am not technical what so ever. PS posted on sxoc too but I know the wealth of knowledge on here is very good. Quote Link to comment Share on other sites More sharing options...
miko_supra Posted July 5, 2008 Share Posted July 5, 2008 (edited) Clutch release arm has come loose off of the slave cylinder? slave or master cylinders shot? how are your clutch fluid levels? check for leaks. Get underneath the car and see where the slave cylinder sits by the side of gearbox (it will be near the bell housing) which will attach onto the clutch release arm, check to see that it hasn't detached from it, and if it hasn't then have someone press the clutch...see if you can see the the slave cylinder moving the clutch arm Edited July 5, 2008 by miko_supra (see edit history) Quote Link to comment Share on other sites More sharing options...
Blackie Posted July 6, 2008 Share Posted July 6, 2008 (edited) John and i both think its a clutch issue. It totally sounds like the Thrust bearing Edited July 6, 2008 by Blackie (see edit history) Quote Link to comment Share on other sites More sharing options...
RedM Posted July 6, 2008 Share Posted July 6, 2008 No chat in Tech please. Quote Link to comment Share on other sites More sharing options...
jamesmark Posted July 6, 2008 Author Share Posted July 6, 2008 John and i both think its a clutch issue. I text the same last night but i just wanted to write in your thread Ido not think it is the clutch as the clutch has not been slipping or showing any signs of going wrong. There has been NO signs of anything in the transmission going worng. Quote Link to comment Share on other sites More sharing options...
jamesmark Posted July 6, 2008 Author Share Posted July 6, 2008 One this I forgot to mention in the symptons is that when I start the car in gear it does the usual jolt fwd and I have pressed the brake and can sit stationary with the car still in gear and wont stall, it is acting like an auto. Quote Link to comment Share on other sites More sharing options...
hadyn Posted July 6, 2008 Share Posted July 6, 2008 I'd say the gearbox is dead mate. I used to have an S14 and one of the few weak points on these cars is the gearbox. They can give up the ghost if driven very hard when the car is tuned to circa 300bhp... Quote Link to comment Share on other sites More sharing options...
supraGZaerotop Posted July 6, 2008 Share Posted July 6, 2008 My UK spec S14a cannot change gear it only started this. No warnings etc and car ran fine up until the point where I went from 4th to 5th and I could not engage 5th. Now when the engine is running I cannot engage any gear. When the car is off I can select all gears. I drove the car for 1 mile in 2nd (as was on my way home from work) and when I depress the clutch nothing happens, the car remains in gear and the revs do not climb. The clutch pedal feels ok maybe a little light but I don'tknow if that's just my imagination. Any ideas guys? I am not technical what so ever. PS posted on sxoc too but I know the wealth of knowledge on here is very good. i had an s14a for 4years mate and i changed over my gearbox in this time, and i only dun 24k in four years in it, very good cars, but gearbox can go:bang: it not treated well and are not running silly power, plus they are noisey as hell. Quote Link to comment Share on other sites More sharing options...
jevansio Posted July 6, 2008 Share Posted July 6, 2008 When my clutch release arm came off the Supe the clutch felt totally different, like there was no resistance at all Quote Link to comment Share on other sites More sharing options...
RobSheffield Posted July 6, 2008 Share Posted July 6, 2008 So, you can put it in gear, start the engine and it tries to move but putting the brakes on stops it? Any noise accompanying that? Id have thought that any mechanical failure in the box would be making a fair racket! Clutch would seem to be the only possible answer. Quote Link to comment Share on other sites More sharing options...
tDR Posted July 6, 2008 Share Posted July 6, 2008 I'd say clutch selector fork is knackered - iirc it was a weak point on the S13 at least and the S14 box is very similar. Quote Link to comment Share on other sites More sharing options...
shaft Posted July 6, 2008 Share Posted July 6, 2008 your gona hav 2 pull the box out buddy, my guess is that therelease bearing has gone through the pressure plate. Quote Link to comment Share on other sites More sharing options...
jamesmark Posted July 6, 2008 Author Share Posted July 6, 2008 There is no noise or grinding from the box. Rob, when I start the car it jolts fwd as it is started in gear (clutch pedal does nothing) and the car moves when acc pedal is used, however when the brake is applied to stop the car and I do eventually stop the car will not stall it just sits there in gear quite the thing, relaease the brake and off we go again all the time the cr has been in gear. Quote Link to comment Share on other sites More sharing options...
jamesmark Posted July 6, 2008 Author Share Posted July 6, 2008 As said before there was no tell tale signs no grinding, no lose of power, no smell absolutely nothing. Even when I came off the slip round and came down all the gears it was as smooth as silk then 200 metres later (fter going up the gears again) 4th to 5th crunched. Stayed in 5th gear as was in a 60 zone and then could not change down gear when I had to turn into my village, I had to force it into 2nd as i did not fancy breaking down in the centre of the road turning in front of traffic. Quote Link to comment Share on other sites More sharing options...
jamesmark Posted July 6, 2008 Author Share Posted July 6, 2008 Ok, just been out to the car and looking down the the gearbox from under the bonnet the slave cylinder that goes into the side of the box is working perfect. The fluid is perfect and is up to the marker. Again car starts in gear and can drive in gear with no noise or grinding, when driving you cannot take it out of gear, press the brake and you will sit stationary in gear (not using clutch). However stop with the clutch depressed then release it (when stopped) the car will stall. So it is going to be going in to the garage tomorrow or Tuesday. Quote Link to comment Share on other sites More sharing options...
adnanshah247 Posted July 6, 2008 Share Posted July 6, 2008 my friend had the same problem, his was a mullered gearbox but a few months before the gearbox went he had some gear linkage problems. Quote Link to comment Share on other sites More sharing options...
jamesmark Posted August 1, 2008 Author Share Posted August 1, 2008 Well I pick her up tomorrow, she is all fixed. I changed the slave and master cylinder seals myself (start with the cheapest repair) Although they needed changed that was not the issue. So £565 bill tomorrow and I get my car back, will find out exactly what went wrong but I have a new clutch fitted as the other one (according to the mechanic) was in a bad way. It was an RPS MAX Street that was less than 12 months old. So I have fitted a stock Nissan clutch as reading up on them on SXOC then can support quite a bit, quite a few people clocked up a lot of miles and running 270 ish bhp. Quote Link to comment Share on other sites More sharing options...
Supranature Posted August 3, 2008 Share Posted August 3, 2008 Well I pick her up tomorrow, she is all fixed. I changed the slave and master cylinder seals myself (start with the cheapest repair) Although they needed changed that was not the issue. So £565 bill tomorrow and I get my car back, will find out exactly what went wrong but I have a new clutch fitted as the other one (according to the mechanic) was in a bad way. It was an RPS MAX Street that was less than 12 months old. So I have fitted a stock Nissan clutch as reading up on them on SXOC then can support quite a bit, quite a few people clocked up a lot of miles and running 270 ish bhp. Your bank manager is a mate of mine, should I warn him now or later?:p:p Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.