Fifty Posted May 7, 2006 Share Posted May 7, 2006 Anyone got one; which is the best? would I be able to use this to polish my turbo pipework in situ - dumb question but Im too skint to buy all these shiny bits from dealers just now lol Rich Link to comment Share on other sites More sharing options...
Jspec Germany Posted May 7, 2006 Share Posted May 7, 2006 I have one dude. Have been pondering that very question. Has anyone used one to polish with? Link to comment Share on other sites More sharing options...
jamesmark Posted May 7, 2006 Share Posted May 7, 2006 i used one on the back of the ashtray with the wire thingy, as previously owned by a smoker, brought it up a treat tbh, never finely polished it though Link to comment Share on other sites More sharing options...
MONKEYmark Posted May 7, 2006 Share Posted May 7, 2006 will take you too long lol. its hard going with a bench grinder with polishing kit.i have had 2 cheap type dremmels and burned motors out on them.just bought another bargain one from car boot for 10 quid it has a stand and flexible arm.worth a try for 10 quid.they great for getting cast marks out.but polishing you will be here next year on same pipe Link to comment Share on other sites More sharing options...
MLC Posted May 7, 2006 Share Posted May 7, 2006 I got a dremmel pro. No idea if it'll polish pipework but compared to some others i've tried it's a bloody animal in comparison (some from Maplins stopped trying to cut through a paper cup, lol). revs adjust from 5k to 33k Been very handy although it'll go through the 'bits' quite quickly on anything metal Link to comment Share on other sites More sharing options...
Fifty Posted May 7, 2006 Author Share Posted May 7, 2006 Ta Wet and dry it is then lol Rich:d Link to comment Share on other sites More sharing options...
JohnA Posted May 7, 2006 Share Posted May 7, 2006 A good idea might be to get a cheap bench grinder and fit polishing cloths to it. I've done it, less than £20 total, maybe below £15 even Bench grinder from Makro, cloths from MachineMart Link to comment Share on other sites More sharing options...
Fifty Posted May 7, 2006 Author Share Posted May 7, 2006 A good idea might be to get a cheap bench grinder and fit polishing cloths to it. I've done it, less than £20 total, maybe below £15 even Bench grinder from Makro, cloths from MachineMart sounds good will have a go. thx Rich Link to comment Share on other sites More sharing options...
Paul Posted May 7, 2006 Share Posted May 7, 2006 I've done some polishing with a Dremel, bloody good tool but not uo to doing big areas. Would be great for getting into the tight areas on pipework but nothing more. Plus the little cloth polishing wheels don't last long and it'll cost you a fortune. One of them tools to get if you've got a few quid spare as it'll come in handy every now and then but that's about it. Paul Link to comment Share on other sites More sharing options...
Guest gzaerojon Posted May 7, 2006 Share Posted May 7, 2006 Anyone got one; which is the best? would I be able to use this to polish my turbo pipework in situ - dumb question but Im too skint to buy all these shiny bits from dealers just now lol Rich won't that be like cleaning a basketball court with a toothbrush? get a nice big buffing wheel for your drill Link to comment Share on other sites More sharing options...
JohnA Posted May 7, 2006 Share Posted May 7, 2006 sounds good will have a go. thx Rich Have a look just above the middle of this pic. You can see the blue bench grinder with the polishing attachment Link to comment Share on other sites More sharing options...
Guest blueangel Posted May 7, 2006 Share Posted May 7, 2006 ive just done said job large area hand sand but like ppl said tight spots it works great. I finished the job off with rubbing compound and a cloth then autoglm and i now have a mirror finish. Link to comment Share on other sites More sharing options...
Jspec Germany Posted May 8, 2006 Share Posted May 8, 2006 sounds good. I guess I need to build a workbench in the basement and then order a bench grinder. Did you use this to polish all your pipework? Speaking of blinging up the motor, where's the best place to have the valve cover done? Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now