Jurgen-Jm-Imports Posted April 27, 2008 Share Posted April 27, 2008 following this thread http://www.mkivsupra.net/vbb/showthread.php?t=148589&highlight=glasgow the car comes out with code 21 and 14 oxgen sensor.. ignition signal.. any gurus that can pinpoint me in the right direction as to what you would do next ? i want to solve the problem asap. the customer started his car today and it was fine for 5 minutes then went to limp mode..(again) the car is stock it does have a boost controller fitted and also a power blitz meter.. am going to get the car brought back to newcastle to fix it but any help to save time would be a bonus.. so the car wont rev past 2500rpm it and idles fine.. but this morning it decided to be ok for 2 minutes.. what do you suggest to replace ? thanks Link to comment Share on other sites More sharing options...
kieren1234 Posted April 27, 2008 Share Posted April 27, 2008 Oxygen sensor - Have you tried a new O2 sensor?? Not sure with the ignition signal. Link to comment Share on other sites More sharing options...
Jurgen-Jm-Imports Posted April 27, 2008 Author Share Posted April 27, 2008 i havent tried anything yet as the car is in scotland, am just trying to avoid buying lots of sensors that are not needed.. if it is a simple sensor then i will post the sensor up to scotland.. am just worried it could be the crank sensor and its a little bit bigger job as you need alternator off etc... Link to comment Share on other sites More sharing options...
Jurgen-Jm-Imports Posted April 27, 2008 Author Share Posted April 27, 2008 bump Link to comment Share on other sites More sharing options...
Steve Posted April 27, 2008 Share Posted April 27, 2008 Just been having a read through one of CJ's manuals. Code 14 -Ignition Signal Try changing the Igniter, if not then ECU. (Doubt its the ECU) Code 21 - Oxygen Sensor Signal More than likely a faulty Oxygen Sensor. If you need more info on tests you can do, i will scan in the pages from the manuals. Link to comment Share on other sites More sharing options...
Jurgen-Jm-Imports Posted April 27, 2008 Author Share Posted April 27, 2008 Just been having a read through one of CJ's manuals. Code 14 -Ignition Signal Try changing the Igniter, if not then ECU. (Doubt its the ECU) Code 21 - Oxygen Sensor Signal More than likely a faulty Oxygen Sensor. If you need more info on tests you can do, i will scan in the pages from the manuals. yes if you dont mind mate Link to comment Share on other sites More sharing options...
Steve Posted April 27, 2008 Share Posted April 27, 2008 Give me 20 minutes Link to comment Share on other sites More sharing options...
Steve Posted April 27, 2008 Share Posted April 27, 2008 http://img2.putfile.com/thumb/4/11713401818.jpg http://img2.putfile.com/thumb/4/11713401851.jpg http://img2.putfile.com/thumb/4/11713401853.jpg http://img2.putfile.com/thumb/4/11713401839.jpg http://img2.putfile.com/thumb/4/11713401874.jpg http://img2.putfile.com/thumb/4/11713401840.jpg That is all the pages to test for a Error Code 14. You should be able to save them and then zoom in. Link to comment Share on other sites More sharing options...
Jurgen-Jm-Imports Posted April 27, 2008 Author Share Posted April 27, 2008 thanks mate do you hav the code 21 ones too Link to comment Share on other sites More sharing options...
Steve Posted April 27, 2008 Share Posted April 27, 2008 thanks mate do you hav the code 21 ones too Hang on, will take a few minutes Link to comment Share on other sites More sharing options...
Steve Posted April 27, 2008 Share Posted April 27, 2008 http://img2.putfile.com/thumb/4/11714192540.jpg http://img2.putfile.com/thumb/4/11714192574.jpg http://img2.putfile.com/thumb/4/11714192534.jpg http://img2.putfile.com/thumb/4/11714192648.jpg http://img2.putfile.com/thumb/4/11714192671.jpg Code 21 Link to comment Share on other sites More sharing options...
Jurgen-Jm-Imports Posted April 27, 2008 Author Share Posted April 27, 2008 thanks mate Link to comment Share on other sites More sharing options...
hodge Posted April 28, 2008 Share Posted April 28, 2008 Code 14 I would have thought it would be the coil pack connectors, i had this code and changed the clips never had the problem since. stick the o2 sensor in some lemon juice over night clean it off and refit it and reset ECU. Hope this helps mate. Link to comment Share on other sites More sharing options...
Jurgen-Jm-Imports Posted April 28, 2008 Author Share Posted April 28, 2008 sorted it was ignator pack Link to comment Share on other sites More sharing options...
kylestt Posted April 28, 2008 Share Posted April 28, 2008 The O2 sensor you can do an Ohm check on the sensor itself. That will narrow down if its the first or second sensor. Link to comment Share on other sites More sharing options...
Steve Posted May 11, 2008 Share Posted May 11, 2008 sorted it was ignator pack Only just remembered this thread. Glad you got it sorted mate Link to comment Share on other sites More sharing options...
Recommended Posts
Please sign in to comment
You will be able to leave a comment after signing in
Sign In Now