Jump to content
The mkiv Supra Owners Club

Underseal service recomendation


Scott-tt
 Share

Recommended Posts

My recommendation would be don't do it.

 

I've had and seen enough older cars where the underseal has either failed or trapped in live rust that it really is something I now avoid like the plague. If you paint a surface or coat it with corrosion preventive then you can see if rust occurs or reoccurs. If you underseal or raptor coat then its out of sight is out of mind.

Link to comment
Share on other sites

My recommendation would be don't do it.

 

I've had and seen enough older cars where the underseal has either failed or trapped in live rust that it really is something I now avoid like the plague. If you paint a surface or coat it with corrosion preventive then you can see if rust occurs or reoccurs. If you underseal or raptor coat then its out of sight is out of mind.

 

What do you recommend ?

Link to comment
Share on other sites

My recommendation would be don't do it.

 

I've had and seen enough older cars where the underseal has either failed or trapped in live rust that it really is something I now avoid like the plague. If you paint a surface or coat it with corrosion preventive then you can see if rust occurs or reoccurs. If you underseal or raptor coat then its out of sight is out of mind.

 

I agree with rider on this point

Link to comment
Share on other sites

My recommendation would be don't do it.

 

I've had and seen enough older cars where the underseal has either failed or trapped in live rust that it really is something I now avoid like the plague. If you paint a surface or coat it with corrosion preventive then you can see if rust occurs or reoccurs. If you underseal or raptor coat then its out of sight is out of mind.

 

Did mine 10 years ago, had no problems, but it's not seen rain in 10 years :)

Link to comment
Share on other sites

What do you recommend ?

 

You could go with pressure wash, steam clean, removing bits that are easy (exhaust, exhaust heat shields, tunnel braces exhaust hanger bracket, tow hook tank guard etc), elbow grease in the hard to reach areas. You will gather the general state from the bits you take off and what you then uncover, as generally how often do we really examine underneath?

 

I did this almost two years ago with one of mine, it was in good enough shape and I didn't plaster it with anything in the end, some dinitrol greasy stuff (under hockey sticks and rear brake duct/vents, I coated the tunnel braces in dinitrol under seal type stuff and por15'ed the exhaust heat shields and fuel tank cover. Also sprayed some acf50 around some places.

 

I had a little look under the other day and may strip it again to see how it's faired.

Link to comment
Share on other sites

What do you recommend ?

 

I'd use POR paint or aquasteel on a prepped surface followed by zinc primer and a matt black or OEM colour paint. For tubular parts or hard to get to parts I spray Dinitrol 3125 which is a wax film corrosion preventive. That way you can see what is going on with the smooth top coat or wax film to know what is going on underneath.

Link to comment
Share on other sites

Got to say I’ve seen quite a few underbody restorations where they cover nuts, bolts, rubber grommets and even some of the lines.

 

Which just hides things and makes things more difficult to remove later on although mine didn’t have rust anywhere, I made the decision just for extra protection long term, although it’s never used in the wet etc, I decided I wanted it done.

 

I’m currently having my complete underbody restoration finished off now by little Num

 

Will start a thread on the project with all the pics once complete

Edited by Supra-love (see edit history)
Link to comment
Share on other sites

I have a UK car which has had to have a fair bit of work, stone guards replaced etc. I too share the concerns that a hard coating/paint can do more harm than good as it can trap moisture accelerating the rust and keeping any corrosion from view.

 

My regime now is to apply some of this every year or two to the whole underside and spray into cavities and gaps. https://www.amazon.co.uk/gp/product/B0035KKK66

 

These creep oils get into everything and displace any water, the down side is that as they are a bit thinner they will eventually wash off.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. You might also be interested in our Guidelines, Privacy Policy and Terms of Use.