Jump to content
The mkiv Supra Owners Club

Why T's Fortune 03 Continuation build!!!


Why T
 Share

Recommended Posts

  • 4 weeks later...
  • Replies 220
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

  • 4 weeks later...
  • 2 weeks later...
  • 4 months later...

So been away from the supra for a while and have a new car purchase but wanting to get back on it.

The fortune broke down a while

Back and would not start. Something with the syvecs.

 

Got this checked by the team at syvecs and it’s fine so one of the sensors has gone.

Just needing to to get Paul @whifbitz to remote in and see what he can see.

 

Also what do people think of this look rather than what I have? With regards to

The spoiler.

 

image

image

 

 

 

 

 

Link to comment
Share on other sites

  • 10 months later...

I've popped back on a nostalgic trip down vehicle memory lane. I have so far discovered that 2 vehicles that I used to own and love (potentially more than my children) have been stripped and sold as parts :( I almost purchased this particular vehicle myself when it first came up in Japan for export (the chop job on the roof put me off). I have gone back through the whole start to finish build thread and still believe that the colour it came in to the country was the best colour its been (for me white lends itself towards a cheap tupperware appearance). Given the current strength in the supra market this motor must now finally be worth the vast fortunes (pun intended) that have been pushed in to it.

Link to comment
Share on other sites

  • 3 months later...

Tbh I’m not [emoji817] what the colour was when it was imported. I believe black. I also feel what is not the collie it should be but that the last thing on my mind with this car. I need a new engine loom and that’s priority atm.

I am hooding that once it’s back up and running to its former glory then it will be worth a pretty penny.

 

 

 

Link to comment
Share on other sites

  • 1 year later...

So Allan Massey said about the forum not being used as much. So here I am.

 

It’s been about 2 1/2 years since she broke down with an error code on the syvecs.

No body could tell me what the problem was fully. So I sent the Syvecs unit back to be checked over and all was fine with it. Which I was happy about.

 

I remember someone telling me about a mechanic local ish to my so have him a call.

He picked it up. Ran some tests. And it turns out that the Engine loom was cause of the problem. New loom done. New sensors all round and some new audi coil packs fitted.

Injectors tested and a ballast for the injectors were missing :(

 

Today I got a video of her running again. Goosebumps!

 

Yes she is vdirty. I need a good detailer is anyone knows of any in East anglia. :)

 

I can’t remember how to upload videos 🤣

 

 

image

 

 

 

 

 

Link to comment
Share on other sites

Wow it must have broke down straight after it was finished did you not have a come back on the fitter ?

Glad to hear it's back running some faults can take time if Intermittent I was chasing down a misfire for about 2 years which turnt out to be a connector in the passenger foot well .

Still hopefully that's the end of the issues and you can enjoy it

Link to comment
Share on other sites

Wow it must have broke down straight after it was finished did you not have a come back on the fitter ?

Glad to hear it's back running some faults can take time if Intermittent I was chasing down a misfire for about 2 years which turnt out to be a connector in the passenger foot well .

Still hopefully that's the end of the issues and you can enjoy it

 

Yea did but they didn’t seem to bothered. Syvecs helped with the ecu. But Whifbitz didn’t really wanna peice from what I remember for whatever reason.

 

I’m hoping so. Some extra stuff is being done to modernize it. Just looking forward to getting it back :)

 

 

 

Link to comment
Share on other sites

So went to MB to look at the car and have a chat. So the wiring for the Syvecs to the sensors were all basically speaker wire. The way the map sensor was fitted is what caused the initial problem with the 5v fault on the Syvecs is what cause the problem. This is actually really frustrating considering how much money was paid for the work.

 

Getting the front brakes refurbed with all new pistons seals and fitting kits.

 

Also changing the injectors to some Siemens Deka 850s I think.

 

Looking forward to getting her back. :)

image

image

 

 

 

Link to comment
Share on other sites

  • 3 weeks later...
So went to MB to look at the car and have a chat. So the wiring for the Syvecs to the sensors were all basically speaker wire. The way the map sensor was fitted is what caused the initial problem with the 5v fault on the Syvecs is what cause the problem. This is actually really frustrating considering how much money was paid for the work.

 

Getting the front brakes refurbed with all new pistons seals and fitting kits.

 

Also changing the injectors to some Siemens Deka 850s I think.

 

Looking forward to getting her back. :)

https://jza80.mkivsupra.net/imports/2020/02/12.jpg

https://jza80.mkivsupra.net/imports/2020/02/13.jpg

 

 

/QUOTE]

 

Are you saying we used speaker wire to wire up a Syvecs? Sorry but thats not the way we do things here, must have been someone else who wired that up?

Link to comment
Share on other sites

Are you saying we used speaker wire to wire up a Syvecs? Sorry but thats not the way we do things here, must have been someone else who wired that up?

 

No mate. What I got told was that speaker wire was used for the engine loom sensors etc. And yes the Syvecs was installed along with all the sensors by Whifbitz I’m afraid to say. [emoji20][emoji17]

 

 

 

Link to comment
Share on other sites

No mate. What I got told was that speaker wire was used for the engine loom sensors etc. And yes the Syvecs was installed along with all the sensors by Whifbitz I’m afraid to say. [emoji20][emoji17]

 

 

/QUOTE]

 

There's no way we would use speaker wire for anything on a car apart from speakers, have you got any pictures of the wire that was used?

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. You might also be interested in our Guidelines, Privacy Policy and Terms of Use.