Jump to content
The mkiv Supra Owners Club

Chris Wilson

Traders
  • Posts

    28855
  • Joined

  • Days Won

    7

Chris Wilson last won the day on August 29 2023

Chris Wilson had the most liked content!

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

Chris Wilson's Achievements

Experienced

Experienced (11/14)

  • Reacting Well Rare
  • Conversation Starter
  • First Post
  • Collaborator
  • Posting Machine Rare

Recent Badges

134

Reputation

  1. You also need the UK 4 pot brake discs, too. Toyota and probably others do the pad anti rattle clips for the 2 pot calipers, but personally I like pads to move about as it reduces the chance of them seizing up. The slider holes in the caliper rackets may be won, that can cause a knock, check the slider pins have their anti rattle square section o RINGS ON THEM STILL.
  2. Chris Wilson

    JR Alloys

    Don't forget that wheel's seat belt....
  3. Chris Wilson

    JR Alloys

    Hi Dunk, good choice, they should look well!
  4. Chris Wilson

    JR Alloys

    Probably over 90% of aftermarket alloy wheels are naff quality, cast from material with inclusions, heavy and often almost impossible to balance due to run out or other seriously defective machining issues. Paying a premium doesn't even guarantee quality these days with so many different manufacturers in the game.
  5. There's a sine to square wave converter module on the back of the speedo housing which can play up, it can cause this issue (especially if it's bypassed with a speedo or top speed delimiter conversion, but that usually manifests itself straight away. The only test is to look at the input to it and the output from it with a two channel oscilloscope, whilst the car is driven. A logging scope or a helper is needed unless you feel confident driving and reading a scope... I have a home for dead ecu#s here and have stopped driving myself crazy with finding good ones. NO ONE over here has proven to be able to reliably fix AND THEN test them, although there's a place in the US that some customers have used successfully.
  6. Borrow a TRAC ecu from a known good car and see if that fixes it, I see a lot of duff TRAC and engine control ecu's these days, finding a good one is a nightmare. Doing all the tests to show if the car has other issues causing the light to flash takes ages, so best to check if it;s the ecu's first.
  7. Will prices go any higher or should I get rid of it now are the figures that REALLY matter
  8. Loads (pardon the pun) of stuff on conrod failure modes available on line, from simple to highly technical 3D stress analysis: https://www.enginebuildermag.com/2017/03/preventing-connecting-rod-failures/
  9. Make sure your standalone ecu is able to resolve a sine wave signal, which is what the stock sensors output, and not in need of a square wave which a lot of more moderns abs sensors output. It's possible to convert the sine wave to a square wave if needed.
  10. It's RPM that kills rods assuming they are of decent design and material for the job at hand. The major strain on a rod and rod bolts is at the top of its travel as the piston tries to exit the bore.
  11. Still around, still do them, and for the J-Spec set up, as well as for many other makes of car and models. [email protected] will find me
  12. Syvecs ECU's can have diagnostics and sensor outputs et cetera read via the LAN cable that you connect the ecu to your PC with. You can download the Syvecs software for free and have a play with it yourself. Same with MOTEC and probably most of the others.
  13. Thanks, I think he's already been in touch, but anyone can ring me, too. 07971*952084
  14. POWER STEERING PUMP WHINNING CAN THEY BE REBUILT?

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. You might also be interested in our Guidelines, Privacy Policy and Terms of Use.