Jump to content
The mkiv Supra Owners Club

mclarenross

Club Members
  • Posts

    638
  • Joined

mclarenross's Achievements

Newbie

Newbie (1/14)

12

Reputation

  1. Drop me a pm with your. Email address and I'll send you my workings out for the wiring of the plugs.
  2. Thanks guys all sorted now, just wanted a plain one to make sure it fits before getting it polished. Thanks
  3. Hi, I'm after a na power steering reservoir. Anyone got one available ? Pm me. Thanks Ross
  4. I'll take this, I'll pm you. thanks
  5. Just read all this thread, great read, going to be a special car once it's finished!
  6. thanks Shawn, they are et0 and didn't need any modification, it was very close though, I did have to remove one of the weights that was on the rim as it was just catching! - - - Updated - - - Thanks, yeah maybe.
  7. Things have moved on a little since my last update, signed up to Scottish Car Mod show in July, so I’ve got my completion date… need to have it done by then. My steering wheel is now back and it really has a WOW Factor. Stevo from on the forum did the carbon work for me and Simon at Hide ‘n Seat Upholstery did the leather, both work is flawless and couldn’t be happier with the service I received! I managed to get hold of a manual gear surround, but the little connector bits were missing of the bottom, so with a little bit of strong adhesive and a bit of filler on a hole that was in the top part, I’ve now got a fully working piece. Also I had some new shiny pulleys delivered and they’re now installed. Had to take the car out of the garage for a few weeks, whilst I had the garage extended so that it can fit the car in lengthways! Couple of pictures sitting outside along with my new toy and the Supra’s baby sitter, the GT4. I’ve also managed to bleed the brakes and my clutch lines, so things are progressing… I’m going to start next on my exhaust and get that all into place and also start getting my intercooler and piping in place.
  8. Thanks Luc, (enjoyed following your build) Well probably time for another update… it’s been so blooming cold up here in the north and I’ve got another project on the go at the minute so don’t have a great deal of spare time to work on Goliath, but as its starting to get closer to the summer I’m starting to crack on with this project. So what have I been doing… well I managed to put all the engine pieces back together attached the manual gearbox and finally get it in the car. (I’ve been wanting to do this for ages!) You can’t see it in this picture, but also start piping in my intercooler pipes with BOV onto the throttle body. I also reattached the anti roll bar and started polishing the top of the alloy radiator. As I’ve got the car up in the air decided to fit all my new brakes, fingers were crossed that they fitted, I knew they would be snug, by wow it’s a tight fit! I’ve also now fibre glassed the rear tub, as one side wasn’t done properly and fitted new braided brake lines all round. Also started to rub down the underneath with a wire brush before I'll be giving it an undercoat. My QTP exhaust butterfly valve arrived just the other day, I'm going to wire this into my dash and attach the valve to the decat pipe so that at the flick of a switch I can open up the exhaust in the middle of the car . (might be a touch loud!) Interior wise, I sanded down all my dashboard panels, and have decided to paint them in Burgandy red, which will go with some of the interior flocking I’ve had done. Next up is to start on the fuel lines and my engine loom, but I made a list to put in my garage, so I can start ticking things off! Hopefully more updates to follow soon...
  9. I've emailed you direct Keron. Cheers
  10. Pm me if you have one spare. Thanks
  11. measured it this morning and its about 9.2mm so I'm going to order some of that 10mm id pipe and some clips to go with it.
  12. yeah I checked eBay first, Id is about 6 mm and couldn't find anything that size. I'll keep looking cheers
  13. yeah, real quality work! thanks mate, the guy who bought the shell also bought the wing! Sorry thanks Chris, great knowledge ! I was going to use silicone hose, so I'll change that plan. I've been having a look around to find some as I need about two meters of it. Any idea where I can get hold of some?
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. You might also be interested in our Guidelines, Privacy Policy and Terms of Use.