Jump to content
The mkiv Supra Owners Club

absz

Club Members
  • Posts

    2466
  • Joined

absz's Achievements

Newbie

Newbie (1/14)

  • Week One Done
  • One Month Later
  • One Year In

Recent Badges

29

Reputation

  1. 1. Josh42 - Staffordshire 2. blythmrk - Derbyshire/Yorkshire 3. erachter - West Sussex 4. Mike2JZ - Zimbabwe 5. Ben_harmer32 - West Sussex 6. Safcdixon - Durham 7. AdamAMG - Mars 8. Tayr - Uranus/Hampshire 9. Lewmc93 - Merseyside / The TSS 10. Mwilkinson - Hampshire 11. m12aak - Leicester 12. Kev.O - Bristol 13. Samurai 20V - South Africa, Durban 14. Trebor69 - Swadlincote 15. Drift_bear - Aberdeen 16. Harrypm82 - Manchester 17. bonus_2000 - Kent 18. Sukhy - Wolverhampton 19. Dnk - Dunk - Redditch 20. Noz - Devon 21. Jim_supra - East Yorkshire 22. Jord - Oxford 23. Style - Newcastle 24. MrGRT - Berkshire 25. kolb - Estonia 26. Swampy - Lincolnshir 27. HamzaHKhan - London 28. WayneW - Belgium 29. sebas - Poland atm 30. Annabella - Lancashire 31. Foxx - Leicestershire 32. Auzzam - London 33.->K1 - France 34. mellonman - SE LondoN 35. Darren - East Sussex 36. Hamilton- Worcestershire 37. absz-Bedfordshire
  2. NA Supra's have the crank pulse sensor built into the distributor which controls spark. when cranking over the engine see if you can spot the rev counter needle bouncing slightly as that's from the crank signal.
  3. I'll start by rechecking the 10amp Ecu fuse located in drivers footwell. but with that blown the car should still crank over?
  4. Some of us old timers are still around lol
  5. Hi Looking for a engine block ideally a 2jzgte but will consider GE. lightly scored bore will be fine as looking to machine out to 87mm building a spare short block as a spare.
  6. If the tensioner and idler are fine then check the crankshaft endfloat if you can.i had a similar issue a few years ago and was due to Crankwalk. Was running a heavy clutch with approx 600bhp.
  7. You let the cat out of the Bag:d
  8. If its the car, I think it is.Then both rear Quarters are repairable will need a replacement wing and door on passenger side.it hasn't been hit too hard to damage any subframes or running gear. also looking at the Vin plate its originally a v160 with a 5-speed gearbox fitted now
  9. absz

    RMS Leak

    Unfortunately it’s a tricky one to comment about without looking at the engine in person. But I would be measuring the distance off how far the seal is pushed in past the seal retainer to make sure it’s a true fitment.also make sure the seal Lip is still pointing inwards and not flipped out which can happen without using a seal fitting tool. Check crankshaft endfloat. And also make sure crankshaft is not distorted by measuring the flange end with a DTI gauge. Others options could be excessive blow-by In crankcase. These are basic checks for any mechanics so I’m sure it’s probably done?
  10. absz

    RMS Leak

    Do you have any pictures of the Leak ? close up
  11. absz

    RMS Leak

    If you have a small groove in the crank were the seal is seated you can normally press the seal further in about 2mm to clear the groove,so sealing lip is on a non worn section.
  12. I'm looking for a shroud only if you willing to split?
  13. Hi Looking for a Viscous/fan and shroud if anyone has one
  14. maybe a loose spark plug ? I'm sure those heat tubes can be screwed out the cylinder head and give you a better chance in getting to plug
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. You might also be interested in our Guidelines, Privacy Policy and Terms of Use.