gaz1 Posted October 25, 2006 Share Posted October 25, 2006 i know this shoud be in techie but need help quick, i am trying to change my indicator bulb, but how the feck do i get to it, cannot find any screws Quote Link to comment Share on other sites More sharing options...
samsupra37 Posted October 25, 2006 Share Posted October 25, 2006 If my memory serves me correct there is one bolt on right hand side and if you turn wheel you can get to it just and a clip on left hand side which allows the light to come forward then you can change bulb...........reverse to put back...........now as you are aware I am not at all technical and this may be complete B******s and my memory is really bad......but I think thats as much help as I can be. If I am right then please let me know as it would probably be a first........ Good Luck Gary;) Quote Link to comment Share on other sites More sharing options...
gaz1 Posted October 25, 2006 Author Share Posted October 25, 2006 lol as bad as me eh, so if i do that the head gaasket will come straight off yeah:innocent: Quote Link to comment Share on other sites More sharing options...
gaz1 Posted October 25, 2006 Author Share Posted October 25, 2006 If my memory serves me correct there is one bolt on right hand side and if you turn wheel you can get to it just and a clip on left hand side which allows the light to come forward then you can change bulb...........reverse to put back...........now as you are aware I am not at all technical and this may be complete B******s and my memory is really bad......but I think thats as much help as I can be. If I am right then please let me know as it would probably be a first........ Good Luck Gary;) then again might just come up and let you have a go;) Quote Link to comment Share on other sites More sharing options...
samsupra37 Posted October 25, 2006 Share Posted October 25, 2006 You will have to tell me how to work the spannery thing........... Quote Link to comment Share on other sites More sharing options...
michael Posted October 25, 2006 Share Posted October 25, 2006 I can get to both of my bulb holders without the need to move the unit or get any tools out - all I used was my hand and a bent wrist. Quote Link to comment Share on other sites More sharing options...
samsupra37 Posted October 25, 2006 Share Posted October 25, 2006 I can get to both of my bulb holders without the need to move the unit or get any tools out - all I used was my hand and a bent wrist. Did you have a spare wrist to bend...that would be very handy...!!!!!TEEEEHEEEE;) Quote Link to comment Share on other sites More sharing options...
michael Posted October 25, 2006 Share Posted October 25, 2006 I have a toolbox full of limbs - I think Halfords sell them. Quote Link to comment Share on other sites More sharing options...
Pete Posted October 25, 2006 Share Posted October 25, 2006 I can get to both of my bulb holders without the need to move the unit or get any tools out - all I used was my hand and a bent wrist. Exactly. The bulb holder twists out the rear. Very easy. Quote Link to comment Share on other sites More sharing options...
gaz1 Posted October 25, 2006 Author Share Posted October 25, 2006 thankyou people job done it was actually a loose wire going into the bulb holder, just managed to get my hand in, then got lots of little cuts from the mesh trying to get it out:D Quote Link to comment Share on other sites More sharing options...
samsupra37 Posted October 25, 2006 Share Posted October 25, 2006 I have a toolbox full of limbs - I think Halfords sell them. I shall have to try there then............ Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.