Notts_TT Posted October 10, 2017 Share Posted October 10, 2017 (edited) Hi Guys I'm building a set of led rear lights, using a 3mm cut alloy composite sign board shaped to perfectly fit in light approx 20mm from lense. Here's my LED set out mock up. So far I've Split lights Cut sign board to fit Bought leds etc Will add more pics soon Edited October 11, 2017 by Notts_TT (see edit history) Quote Link to comment Share on other sites More sharing options...
Notts_TT Posted October 10, 2017 Author Share Posted October 10, 2017 (edited) Once lights are done I'm going to mix a sniff of black paint with some 2k lacquer and tint them properly, not too much so you can't see leds but enough to look stealthy Edited October 10, 2017 by Notts_TT (see edit history) Quote Link to comment Share on other sites More sharing options...
AC93 Posted October 11, 2017 Share Posted October 11, 2017 Look forward to seeing them in action! Quote Link to comment Share on other sites More sharing options...
Notts_TT Posted October 11, 2017 Author Share Posted October 11, 2017 In pics I have cut the alloy plate to stick to the plastic insert which was trimmed so Plate sits better, then wrapped it in a 4d car on wrap, then cut the file I created of 5mm holes where I want the leds to sit ready to drill, last pic is the stencil stuck to plate. Time for some soldering and adding resistors I think. I bought White leds Orange leds And 2 powers of red leds, one for side one for brake.. I tested them all and all seem to be a good brightness Quote Link to comment Share on other sites More sharing options...
SupraP-Z Posted October 11, 2017 Share Posted October 11, 2017 Been thinking i want to attempt something like this, seen some decent designs around recently. Look forward to seeing how these come out! Quote Link to comment Share on other sites More sharing options...
el_bandido Posted October 12, 2017 Share Posted October 12, 2017 I was contemplating using some resin or plastic to direct the light (much like Audo/Lambo do) to give a more continuous light. Any thoughts on this? Quote Link to comment Share on other sites More sharing options...
Notts_TT Posted October 12, 2017 Author Share Posted October 12, 2017 I was contemplating using some resin or plastic to direct the light (much like Audo/Lambo do) to give a more continuous light. Any thoughts on this? You mean for the backing plate ?? These leds are really directional and only project light out, it's not really a spread of light. Quote Link to comment Share on other sites More sharing options...
Kendo11 Posted October 12, 2017 Share Posted October 12, 2017 Nice project. I bought some of the sheets and was tempted to have a go but ended up going down the COB route. Quote Link to comment Share on other sites More sharing options...
Notts_TT Posted October 12, 2017 Author Share Posted October 12, 2017 Nice project. I bought some of the sheets and was tempted to have a go but ended up going down the COB route. Cob ? Quote Link to comment Share on other sites More sharing options...
Kendo11 Posted October 12, 2017 Share Posted October 12, 2017 Cob ? Rings Quote Link to comment Share on other sites More sharing options...
jagman Posted October 12, 2017 Share Posted October 12, 2017 cob -chip on board , available in red ,amber, white , usually around 14 cm x 1 cm -or rings , very low current draw and produce a straight line of constant light which is very bright -no drilling required and dimmable , also very fast switching times Quote Link to comment Share on other sites More sharing options...
Notts_TT Posted October 12, 2017 Author Share Posted October 12, 2017 Sounds good, did look at those rings but you don't see that many full panels of leds in supra lights so thought why not. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.