CarlT67 Posted April 12, 2017 Share Posted April 12, 2017 I'm possibly looking at a set of Works Sizes will be 9.5j ET +35 front 10j ET +35 rear These will fit I believe and look pretty nice. Is this enough of a stagger front to back? The only other option is 10.5j on the rear but that comes in a +20 offset which I don't think will fit?? Quote Link to comment Share on other sites More sharing options...
Dim Sum Posted April 12, 2017 Share Posted April 12, 2017 What size wheels? 18" or 19" Also might be good to put down what tyre size you planning to use Quote Link to comment Share on other sites More sharing options...
HarleyFDMD Posted April 12, 2017 Share Posted April 12, 2017 10j +35 will be fine 10.5j +20 wont fit atall. You'd need rolled arches, mad camber and stretched tyres to get that under the arch Quote Link to comment Share on other sites More sharing options...
HarleyFDMD Posted April 12, 2017 Share Posted April 12, 2017 Give me a minute and il get you some pictures of mine that you can reference Quote Link to comment Share on other sites More sharing options...
CarlT67 Posted April 12, 2017 Author Share Posted April 12, 2017 What size wheels? 18" or 19" Also might be good to put down what tyre size you planning to use 18" Something like 245 front 275 Rear 10j +35 will be fine 10.5j +20 wont fit atall. You'd need rolled arches, mad camber and stretched tyres to get that under the arch /QUOTE] I thought that would be the case no chance of fitting with them offsets. Quote Link to comment Share on other sites More sharing options...
HarleyFDMD Posted April 12, 2017 Share Posted April 12, 2017 Ok so the picture below is a 10j with an offset of +25 I have rolled arch that allow me to run the lower offset. Your potential wheel specs with the +35 offset will sit 10mm further into the arch. I would hazard a guess that that would sufficiently clear stock arches but if not the very most you would need would be a very minor arch roll. Quote Link to comment Share on other sites More sharing options...
HarleyFDMD Posted April 12, 2017 Share Posted April 12, 2017 Again with the front, The below picture shows an 8.5j wheel with a +10 offset. Again i have rolled arches. Your potential 9.5j et35 would sit 12mm further into the arch and again i would guess that would be ok but at the very most you'd possibly need a minor arch roll. Quote Link to comment Share on other sites More sharing options...
CarlT67 Posted April 12, 2017 Author Share Posted April 12, 2017 Again with the front, The below picture shows an 8.5j wheel with a +10 offset. Again i have rolled arches. Your potential 9.5j et35 would sit 12mm further into the arch and again i would guess that would be ok but at the very most you'd possibly need a minor arch roll. https://uploads.tapatalk-cdn.com/20170412/1b8ee74050ac9d9547291723137cdc57.jpg https://uploads.tapatalk-cdn.com/20170412/e32503b33e06881683e7b3fafd42c24d.jpg /QUOTE] Thanks very much for your help! Quote Link to comment Share on other sites More sharing options...
HarleyFDMD Posted April 12, 2017 Share Posted April 12, 2017 No worries mate. Wheels and offsets can be a real pain if you have no references to go off Quote Link to comment Share on other sites More sharing options...
CarlT67 Posted April 12, 2017 Author Share Posted April 12, 2017 I know I'm trying to work it out from my current wheels, previous wheels and loads of searches comparing to other peoples. The struggle comes as not all wheels come in all width and offset combinations you want. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.