AEM Infinity

Out of curiosity is anybody running the AEM?

Might be a few members running it for a while now, do you recommend it

Gpro is running one but swiftly got mkivsupra.neted for posting about it as it looked to be a sales thing

That's the route I'm taking in the next month or two.

Lots of decent hardware upgrades from the series 2. Loving the can bus BTi gauge which is much like the toucan for the syvecs.

That's the route I'm going. I believe a custom loom is currently required.

I'm NA-try though so GTE might be okay.

Gpro is running one but swiftly got mkivsupra.neted for posting about it as it looked to be a sales thing

? what are you on about? and yes I do have the AEM Infinity

That's the route I'm taking in the next month or two.

 

Lots of decent hardware upgrades from the series 2. Loving the can bus BTi gauge which is much like the toucan for the syvecs.

 

That's the route I'm going. I believe a custom loom is currently required.

 

I'm NA-try though so GTE might be okay.

I wish there was a 52mm syvecs gauge setup. I don't really want a big 'ol toucan on my dash, but as I want the info available I may be forced into it!

I wish there was a 52mm syvecs gauge setup. I don't really want a big 'ol toucan on my dash, but as I want the info available I may be forced into it!

I thought the same, but honestly the Toucan is much smaller than you expect. I've managed to integrate mine well into the dash

Much more oem looking than gauges

? what are you on about? and yes I do have the AEM Infinity

Didnt you fit yours then did a right up about how good it was then the mods got funny with the thread cos it looked like a sales pitch I cluld have swore it was somthing like that

I thought the same, but honestly the Toucan is much smaller than you expect. I've managed to integrate mine well into the dash

http://i297.photobucket.com/albums/mm203/j_s14a/Snoopy%20Supra/DSC_0141_zps5mjgxk9b.jpg

 

Much more oem looking than gauges

I must admit that's the first toucan I've seen that looks ok, colour matches the dash panels very well.

Usually they look a right eye sore.

Didnt you fit yours then did a right up about how good it was then the mods got funny with the thread cos it looked like a sales pitch I cluld have swore it was somthing like that

Yeah, I did a write up as it was and still is a brilliant ECU so I stand by that. Regarding mods getting funny, this is the first time I'm hearing this

Funny how it sounded like a sales pitch, as I never offered or tried to sell one. My career isn't in cars or ECU's.

? what are you on about? and yes I do have the AEM Infinity

This is what I was on about, would of thought you would have remembered the thread

http://www.mkivsupra.net/vbb/showthread.php?306025-AEM-Infinity-ECU-Review/page2

Still its a good review

How you finding it GPro , Did I read on Supra Forums members had an issue when it was launched with Idle on cold start up bit I think it was since fixed with a firmware update

Just reading up about it I think it just needs a Map sensor and the Fuel / Oil pressure are extra's for the fail safes , maybe a Bosch LSU

What did you get in the kit? ECU and Mkiv Loom?

I dont think it will control the stock twin sequential turbos , I will need to go TTC

How you finding it GPro , Did I read on Supra Forums members had an issue when it was launched with Idle on cold start up bit I think it was since fixed with a firmware update

 

Just reading up about it I think it just needs a Map sensor and the Fuel / Oil pressure are extra's for the fail safes , maybe a Bosch LSU

 

What did you get in the kit? ECU and Mkiv Loom?

 

I dont think it will control the stock twin sequential turbos , I will need to go TTC

My kit came with Mkiv PnP harness, map sensor, fuel pressure sensor, boost solenoid, air intake temp sensor, 12 position switch and wideband sensor.

At a minimum you would need the wideband/Bosch sensor, the ECU can work with your stock map sensor. Fuel pressure is optional, but highly recommended for accurate close loop.

Latest firmware seems to be stable, as far as I'm aware.

This is the package I got. http://fsrmotorsports.com/component/virtuemart/?page=shop.product_details&flypage=flypage.tpl&product_id=19&category_id=20&Itemid=87

but, this cheaper package should be fine for most users. http://fsrmotorsports.com/index.php?page=shop.product_details&flypage=flypage.tpl&product_id=257&category_id=20&Itemid=87&vmcchk=1&option=com_virtuemart&Itemid=87

Thanks , the ECU did catch my eye when it was launched but it does not seem to be popular here across the board in the EU for some reason , few skylines etc run them

Spec wise it does seem to be great value , is there any cool apps, software , gadgets you can use with it?

Few videos on YouTube of them testing the safety features.

Spec wise it does seem to be great value , is there any cool apps, software , gadgets you can use with it?

If i had an AEM Infinity i'd use the video converter from gauge art to display all the gauges on my headunit, its a shame they don't support syvecs.

http://www.supraforums.com/forum/showthread.php?824489-GaugeART-Review

Its all about if you can get a decent mapper to work on it, also don`t believe any of this self mapping bullshit.

Thanks guys, it's dimitri from Greece who would most likely map it

If the AEM gauge is CAN based it could prob be made to work with a Syvecs

EDIT: same goes for the gaugeArt

Those gauge art gauges do look nice!

But a little bit gimmicky

I do like an analogue mechanical gauge , maybe I am getting old

If the AEM gauge is CAN based it could prob be made to work with a Syvecs

 

EDIT: same goes for the gaugeArt

How did I never know about this previously!!!! I need this in my life!!! I'm 100% going this route with my infinity.

I need a new head unit anyway. That's top notch