Jump to content
The mkiv Supra Owners Club

996 Turbo Project! ***Page 3 Update***


Slutters
 Share

Recommended Posts

Hi guys

 

After moving on from my Single 6 Supra i brought my dream car, a 996 Turbo with 46,000M in fantastic condition.

 

Got a few pictures for you lot, nothing like the Supra as i am TRYING to keep it stock and original.... :taped:

 

Anyway here she is:

 

image

 

I gave her a full service and changed the CD player for something a little more modern.

 

Next up was the brakes, the lacquer was starting to peel of the calipers and looked a bit messy, so i set to work.

 

I sent away the calipers and heres what came back!

 

image

 

Shot blasted, powder coated and new seals with stainless steel nipples. :)

 

While i was there i removed all the steel bolts and replaced with stainless steel

 

image

 

image

 

image

 

image

 

Also waxed oil'ed the pipes and other parts

 

image

 

image

 

Fitted all new link pipes, brackets and bolts along with stainless steel lines

 

image

 

image

 

image

 

image

 

image

 

image

 

image

 

image

 

image

 

New pads, discs were ok so bells primed and painted

 

image

Link to comment
Share on other sites

  • Replies 59
  • Created
  • Last Reply

Top Posters In This Topic

Great motors, been tempted for a while too :thumbs:

 

Cheers guys

 

Go for it! Amazing cars, no match for a Single on a straight road but would mash one in a corner. You get a good 570NM at 2700RPM with no lag which means leaving a corner your back on the power while the Supra would still be spooling. :)

Link to comment
Share on other sites

Cheers guys

 

Go for it! Amazing cars, no match for a Single on a straight road but would mash one in a corner. You get a good 570NM at 2700RPM with no lag which means leaving a corner your back on the power while the Supra would still be spooling. :)

 

Is yours tip or 6 speed ?? Id put mine up against any single sup up to about 650 ish at the moment, its the way it puts the power down !!! Hopefully ill be around 600hp in a week or so as the motors out at the moment.

Link to comment
Share on other sites

  • 1 month later...

Hi guys bit of an update!

 

Tried a new exhaust and did a few more bits that I have been wanting to do.

 

Started stripping the rear end, lights and bumper removed.

 

image

 

image

 

Remove the arch liners

 

image

 

image

 

image

 

Found one of the top boost pipes was not properly connected! Always boosted ok. With that in mind, intercooler out

 

image

 

image

 

image

 

Here you can see the situation that greets most Turbo owners… rusty nuts!

 

image

 

The manifold to head bolts were the same… (I removed one and then took the pic)

 

image

 

image

 

Thankfully they all came undone with no snapped bolts!

 

I replaced all of them with new Stainless steel bolts!

 

image

 

image

 

image

 

The turbo’s and manifolds were not so easy…

 

image

 

image

 

image

 

image

 

Heatshields and mounts well rusted!

 

image

 

However after lots of heat with a Oxycet torch we had them off!

 

image

 

Drivers side ready for new exhaust! New threads and brass nuts so no more corrosion, also replaced the turbo mount bolt and nut for stainless

Link to comment
Share on other sites

image

 

image

 

image

 

 

 

Also as I was there I decided to do a plug and coil pack change!

 

image

 

image

 

Old plugs

 

image

 

6 x Coil packs and plugs

 

image

 

Passanger side done with new bolts

 

image

 

Started on the drivers side

 

image

 

This is a 48K mile coil pack! Good job I changed them

 

image

 

 

image

 

New ones in place

 

image

 

 

New heatshields

 

image

 

image

 

image

 

VHT painted and left to cook on the wood burner

 

image

 

Also stripped and repainted the coil pack covers, using more stainless bolts

 

image

 

image

 

Looking much better now

 

image

 

image

Link to comment
Share on other sites

Also replaced the alternator reg and rear bearing as it was not charging well

 

image

 

image

 

image

 

I wanted to replace the side bumper heatshields as they were corroded. I didn’t want to use the original fixing method as they seem to rust up, so I modified them to take stainless steel fixings

 

Stripped the old intercooler brackets down

 

image

 

image

 

image

 

These hold the heatshilds at the bottom of the bumper, you can see how rusty they get

 

image

 

So cut off the old fixings and drilled a hole out in the same location as they were in.

 

image

 

Then welded some stainless bolts in to the holes

 

image

 

image

 

And there we go, stainless fixings that will always come undone

 

image

 

Also used some new arch liner fixings as the old ones were rusty

 

image

 

Stripped the paint of the brackets and gave them a primer and paint

 

image

 

image

 

 

Also gave the intercoolers a good clean!

 

Before

image

 

After

image

 

image

 

Made a start fitting the intercooler packs back together

 

image

 

New duct sealing tape on

 

image

Link to comment
Share on other sites

image

 

Ready to refit

 

image

 

image

 

Now to show you the exhaust!

 

Here is what I removed

 

image

 

Here is what I fitted!

 

image

 

So new heatsheilds and exhausts on using brass nuts!

 

image

 

image

 

image

 

image

 

As I was fitting new exhausts I wanted some fresh lambda sensors

 

image

 

image

 

image

 

image

 

Intercoolers back on with stainless hardware

 

image

 

Got some new heatshields to replace my old rotting ones

 

image

 

Originally the heatshields are direct on the steel frames which I imagine helps wear them away until the fall apart and rattle.

 

So with this in mind I brought a sheet of rubber and cut washers to stop them rubbing

 

image

 

image

 

image

 

Rubber washers around the new stainless threads I added to the intercooler frames

 

image

 

Chassis mounts for the heatshields

 

image

Link to comment
Share on other sites

2nd rubber washer on the other side of the heatshield

 

image

 

Stainless washer and nut to finish them off

 

image

 

Drivers side

 

image

 

While I was there I replaced some of the arch and side skirt screws with new ones as some were going rusty

 

image

 

image

 

image

 

image

 

image

 

image

 

All bolted back together and ready for a run!

 

image

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. You might also be interested in our Guidelines, Privacy Policy and Terms of Use.