Rear Wheel fitments?

Hi all,

Another wheel thread, I was wondering if the following would fit the rear of a stock supra? and if so would it require an Roll of the arch?

The wheel spec is as followed-

18" 10.5J ET24

Thanks in advance

EDIT- another set of wheels in question see post 31...

They'd stick out around 15mm past the stock wheels arches.

They'd stick out around 15mm past the stock wheels arches.

Past wheels or arch? would this mean they should clear with a mild roll?

The rear wheels in the pic are 18x10 +32

18x10.5 +24 would stick out 14mm more in comparison, you'd either need wheel arches or have the stock arches pulled out by around 14mm - which I'm not sure is doable.

Damn Thanks Nic

Or go stretched tyres and lots of camber

No camber happening here, would go a mild stretch if I really had too but to loose 15mm is going to be pushing it to far. Want it to look good.

Hence the " "

Marc(AB10)'s Works are 18x11 et22 (or 24, can't remember which) and he has stock arches with a roll. Though he is mega low on coilovers so there is a bit of camber there.

Hence the " "

 

Marc(AB10)'s Works are 18x11 et22 (or 24, can't remember which) and he has stock arches with a roll. Though he is mega low on coilovers so there is a bit of camber there.

Yeah his looks awesome too, but that look would need my archs to be pulled too, plus the slammed look on the island is going to end in tears. It scrapes everywhere now and im on stock springs.

Roll the rear arch and run a 265 tyre and you will be alright, I run 18x10 et20 with 255 on and it scrubs but then again I haven't rolled my arches

would a 265 on a 10.5 j rim not look very streched?

Would be similar to what Porsche run standard on some of their wheels, more a tweak then a stretch. 255 would be ok on 10.5 I stated a thread a while back about tyres on rims and someone posted min / ideal / max tyre width for wheel widths

Just checked and it was you lol

I'd say that's a bad offset for a 10.5J wheel if you don't want serious fender mods. I'm running 10.5J with ET40 and the wheels already look pretty aggressive. 275 tires on mine already look a bit stretched.

Such a shame, cheers guys but looking at that pic above means its guna be a no go. Shame as found a bargin set of rears thats all

What are these wheel you were looking at ? Is it just rears or a staggered set ?

Such a shame, cheers guys but looking at that pic above means its guna be a no go. Shame as found a bargin set of rears thats all

EDIT : Question was asked above.

Think he may be looking at the 19" wheels scooby slayer has for sale ,the volks one.

If so I'm not sure with 19" if a stretch would work

Think he may be looking at the 19" wheels scooby slayer has for sale ,the volks one.

 

If so I'm not sure with 19" if a stretch would work

Don't think so mate. He said they were 18". 10.5J, ET24 and 19" would be nuts, you'd have to cut a chunk off the fender lol

do it, roll the archs slightly. not a huge job mate

No not his mate the wheels where a pair of rims on Driftworks-

http://www.driftworks.com/forum/wheels-tyres-sale-private-sales/180113-pair-18-10-5j-et24-garson-wheels-black-polished-lip.html

Was going to get them and a Pair of Roat D2's for the front to give me the SSR or Work meister look for half the price.

I would be tempted to bite the bullet, my wheels have room to go wider if I rolled the arches

If they will fit with a roll i will go for it, but judging by the info looks as though they wont.

The rears on that look good! is that the same spec as i have enquired about then?