Jump to content
The mkiv Supra Owners Club

Jamesy's Billet 6765H Single Conversion ...!


Jamesy
 Share

Recommended Posts

Right this is the new thread as the other one was started a bit early and didnt have enough pics for some members :)

 

Work begun on this project yeserday ......

 

 

I have decided to go with the impressive Billet 6765H DBB .81ar Turbo!

 

Would like to see 630-650bhp once Ryan has finished and then next year will sort out a complete new fuelling system with Lee to get over 700bhp :)

 

 

All the work is being done by Lee at SRD who i cannot recommend highly enough:

http://www.supraracingdevelopment.co.uk//

 

And the mapping will be done by Ryan G at 2bartuning:

http://www.2bartuning.com/

 

 

My car is currently at BPU level so some modifications have already been done, although most of it will be replaced during the conversion:

 

* Walbro 255lhr fuel pump

* Blitz DD Bov

* CW 1st and 2nd decat pipes

* CW R/Ring

* Thor FCD

* Blitz dual SBC type R boost controller

* GReddy FMIC

* Denso iridium plugs

* Oil pressure and Oil temp gauges

* Boost gauge

 

Before:

image

 

 

After: :D

image

 

image

 

image

 

 

 

 

Below is the spec i have decided to go for:

 

* Billet 6765H DBB Turbo with .81ar :D

 

* Custom SRD Heat Shield

 

* Modified OBX 321 stainless steel manifold

 

* HKS 50mm wastegate with screamer pipe :D

 

* 4" Full-Race Pro Sport downpipe

 

* 4" Full-Race Pro Sport mid pipe

 

* 4" HKS Ti catback exhaust :D

 

* 4" SRD Front Mount Intercooler with custom piping

 

* 4" Inlet pipe and K&N air filter

 

* SARD 800cc drop in injectors

 

* SRD Stage 2 Race Cams :eyebrows:

 

* Brian Crower uprated springs and retainers

 

* HKS cam pulleys

 

* GReddy Plenum, throttle cable and TPS adaptor

 

* Q45 Throttle body

 

* GReddy timing belt

 

* F-Con V Pro Gold ECU

 

* Bosch 044 fuel pump

 

* AEM AFR gauge and wideband sensor

 

* AEM trans temp gauge

 

* Blitz oil cooler and relocation kit

 

* 2 x SRD Gearbox coolers

 

* Gearbox cooler gauge

 

* Uprated Boostlogic autobox (built by Michel Lane)

 

* 3800 Hi Stall torque converter

 

* Line lock kit

 

* BC Racing fully adjustable coilovers

 

* LSD

 

* UK Spec brakes front and rear with 3G drilled and vented discs and CW fast road pads

 

* Resprayed UK Calipers in silver with black decals

 

* CW braided brake hoses front and rear

 

* Alloy Overflow Tank

 

* GReddy Timing Belt

 

* Fuel Pulsation removal kit

 

* FPR, gauge and rail adaptor

 

* New Water Pump

 

* New valve stem seals

 

* TRD Thermostat

 

* SRD Polished Greddy Manifold, Q45 Throttle Body, Water Neck & Cam Covers

 

 

Will keep this thread updated as we go!

 

 

 

image

 

image

 

:D

 

 

*** Updated pics ***

 

image

 

 

image

 

 

image

 

 

image

 

 

vHOHtGvTHq8

Edited by Jamesy (see edit history)
Link to comment
Share on other sites

  • Replies 1.2k
  • Created
  • Last Reply

Top Posters In This Topic

If I were using XS Power anywhere I think the DP/MP must be the safest bet, hell it's only a length of pipe :D

 

Good luck with the project, it's in good hands, and in for the updates

 

I had the xs power down and midpipe on my blue supra and they were a mile away I had to take them into work to be modded.

Did you get the exhaust from captain chaos. Sounds like his old system jamesy

Link to comment
Share on other sites

I had the xs power down and midpipe on my blue supra and they were a mile away I had to take them into work to be modded.

Did you get the exhaust from captain chaos. Sounds like his old system jamesy

 

Yes mate i did - to be honest its at the welders now as wasn't in tip top condition around the joins so we'll see what they can do with it and offer it all up soon - if it fits then great if not we'll go a different route :)

Edited by Jamesy (see edit history)
Link to comment
Share on other sites

Might have to change my wheels soon :(

 

I really like them but they are 18x9.5 rears and with the new power traction may become a real issue.... on the lookout for some seriosuly deep dish alloys something like 18x11.5 rears.

 

(If anyone can find the ones i currently have "Vertec Manary Sport" please let me know as i'll just buy two 18x11.5 for the rears and put the current rears on the front :) )

Link to comment
Share on other sites

To get us started here is a couple of pics of the engine bay before we begin. :)

 

image

image

image

 

Very nice turbo should give James the spool and power he was looking for. :)

 

image

image

image

 

Starting the strip down, no going back now mate. :)

 

image

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. You might also be interested in our Guidelines, Privacy Policy and Terms of Use.