Jump to content
The mkiv Supra Owners Club

Rinus gt4082 build


Rinus
 Share

Recommended Posts

He good people ;)

 

Like to share some pictures of my setup...

 

Started with;

 

Cast-manifold (turbonetics)

Garrett Gt4082jb

Mines wastegate 35mm

Aem intake

Xs-downpipe

 

image

image

image

image

 

At first drill out the wastegate of the manifold, it was a bit small, 32mm;

image

 

Now it matches the mines wastegate 35mm;

image

image

 

Modify the downpipe,

first cutting 3cm off the beginning of the downpipe,

where pipe connects to turbine;

image

image

 

After that cut out 5cm in the middle of the pipe;

image

image

image

 

And 10cm at the end of the pipe;

image

 

Ready to weld;

image

 

Testfitting;

image

image

Link to comment
Share on other sites

And getting the screamer pipe back in exhaust;

image

image

image

image

image

 

My first time wrapping ever, so be gentle...:D

Will get the T-rips offff:Pling:

image

 

Oil drain, with custom made flanges;

image

image

image

 

Blockoff waterfeed, pipe has been pearled (no its not a new one :D);

 

image

 

Has anyone an idea what the big sensor is for?

Does it acctivate the little airco fan when its getting too hot?

Cause I thougt myself the sensor at the bottom of the radiator does that...

The little one is for the stock temp gauge I think?

 

2 spal fans, thats why I like to know about the sensors:);

I bought one sensor 87-82 degrees, dont know best place to fit...

image

 

Right know I'm waiting for the vband flange from garrett,

for the outlet of the compressor (to fmic piping)

This is smaller than 3inch and bigger than 2,5inch :blink:,

7,39cm cross-cut...

Cause of the vulcano problems I'm waiting 6weeks already :innocent:

 

 

If you guys have any comments, good or bad, will appreciate that...

 

Cheers Rinus

Link to comment
Share on other sites

on the water pipe, the small sensor is for engine temp guage, the other is for ECU I belive.

 

Yes, that's how they are. Very nice set up, cast manifold, flexi sections in both down and wastegate exit pipes, and neat welding :) It should be a reliable set up. My only concerns would be the small amount of material around the hole for the wastegate, if anything is going to warp and blow it will probably be there, but there are options to retrieve it if it does. The other is are you sure that turno oil drain hose is up to the temperatures involved? It also looks a bit small on the ID of the fittings, but a ball bearing turbo doesn't flow that much oil around the cartridge, so it will probably be adequate. Please posy more info as it progresses :)

Edited by Chris Wilson (see edit history)
Link to comment
Share on other sites

My only concern would be the small amount of material around the hole for the wastegate, if anything is going to warp and blow it will probably be there, but there are options to retrieve it if it does.

 

Do tell Chris, as I have a similar set up...

Link to comment
Share on other sites

You could have a square section groove machined in the manifold or wastegate flange to take a ring, of the type similar to where the stock turbos mount onto the stock manifold. They allow some movement and still maintain a seal. I think Wez had the adaptor welded on, but maybe that was due to cracking?! :)

Link to comment
Share on other sites

Ok,

I hope it will hold around the wastegate,

I think its no option to weld a stainless steel wastegate flange,

to the cast-manifold?

But its a good idea for a ring groove drilled if it blows...

 

@ chris its journal-bearing, so a bit more oil will get trough the oil drain...

The material of the oildrain is an hydraulic-hose 300bar,

outside is sort of plastic, but inside its steel...

So if it melts I will first smell it...

Thinking of some sort of heatwrap/tape around it,

I will measure the smallest hole of the oil drain,

I think it should be big enough or is there a minimum size for an oil drain, for journal-turbos?

Link to comment
Share on other sites

If you are in doubt I would refabricate using mainly alloy or steel tube with connectors made of silicone with a flouro/silicone liner. The liner isn't vital, but stops long term osmosis of the oil through the tube walls. I use these people as they are local, but their delivery can be unreliable..... http://www.viperperformance.co.uk/plainpage.php?pgId=28

 

I would aim for 12 or 13 mm bore pipe and push on fittings. Swaged and crimped bolted fittings have too small an internal diameter to use with sensible hose OD sizes for this sort of application. Look at the size of the drains on a stock 2JZ-GTE or RB26DETT engine to see what the manufacturers use, they are quite big ID hoses.

 

Not criticising, it's just that a restricted or unreilable turbo oil drain can cause serious problems.

Link to comment
Share on other sites

I appreciate that you give your opinion,

than afterwards comment when I blew up the car...

I will compare my oil drain with de stock one and then make a decision...

I'm not affraid of melting,

have seen a frien of mine with tubular manifold,

with on the compr-outlet a 90degrees plastic pipe only 1/2 inch from the manifold and no burning or melting [sHOCK][/sHOCK]

 

The watertemp.sensor for the ecu (the bigger one in the elbow),

what doe the ecu with these data?

Link to comment
Share on other sites

I think Wez had the adaptor welded on, but maybe that was due to cracking?! :)

 

I had issues at Marham where it blew the wastegate gasket out, I replaced it but it happened again so I removed the gasket, cleaned the faces, bolted it down and had it welded. Hasn't given me an issue since.

 

My cast manifold was modified by Induction Motorsport, they build up material around the wastegate port and then bore it out.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. You might also be interested in our Guidelines, Privacy Policy and Terms of Use.