Jump to content
The mkiv Supra Owners Club

Project 1300


suprafan72
 Share

Recommended Posts

All,

 

I am starting this thread as I am wanting to take my new bought supra which is

 

http://www.jm-imports.co.uk/cardetails/toyota/2009/SUPRA20.html

 

My plans are to do the following :)

 

I want to run a 1000 horsepower plus on pump fuel and intend to do what it takes to get there..... Some of the intial things im looking at doing are :-

 

Suspension and Brakes

New CW suspension

New discs and performance pads

Full Geo Setup

 

Exterior

Painting wheels dark grey to black

New facelift fronts and rears

Front bumper repainted (as there are stonechips on it)

Intercooler pipework polished.

Windows tinted (to make it look hard as nails)

 

Engine

 

Aftermarket Plenum.

W/I System.

Bosch 1200cc high imp injectors

Twin feed fuel rail

Aeromotive FPR

Aeromotive Filter

2 X Walbro fuel pumps

PHR triple pump hanger

Upgraded fuel lines -10 to twin feed -6

Installation of a PHR Single turbo kit with a 76mm billet turbo

 

Interior

 

Boot build (probably similiar to Jamie P's

Seats retrimmed in leather with matching harness's

Short shifter gear stick

AEM wideband

Fuel pressure

EGT Gauges

 

The car allready has a massive specs on it which currently is

 

3.1 Litre Full Tune Engine by Front Row (Around 15000 kms ago)

Carrillo Conrods

87mm Forged Pistons

272 Camshafts

Twin Greddy TD05 Turbos (Polished)

Dual Waste gates

Lightweight Bonnet

Polished Intake Plenum

Oil Cooler

ATS Mutliplate Clutch

Aftermarket LSD

Earls Lines and Connectors in Engine Room

Uprated Fuel Pump

Braided Top Rad Pipe

Custom Painted Cam Gear Cover

Polished Cam Covers

Cusco Front Strut Brace

Massive Alloy Koyo Radiator

Large Front Mounted Intercooler and Custom Piping

Apexi Dual Induction Filters

Custom Suction Pipes

Aftermarket Manifolds

Aftermarket Front Pipes

SARD 850cc Injectors

Custom Turbo Heatsheilding

Cusco Rear Strut Brace

Front Row SPL Apexi N1 Coilovers

Bestex Springs

Cusco Pilo Uppers

Supra Large Model Calipers

Rear Stainmesh Brake Lines

Uprated Rear Rotors

Alloy Rear Diffuser

Abflug Front Aero Bumper

Custom Front Row Exhaust System

Brembo F50 Brake Kit

ARC Front Anti Roll Bar

Adjustable Fuel Pressure Regulator

HKS FconV Pro

7 Point Roll Bar with Padding

Recaro Bucket Seat for Driver

Willans 4 Point Harnesses

Recaro Passenger Seat For Passenger

18" BBS LMs

Momo Suede Steering Wheel

HKS EVC Boost Controller

Greddy Oil Temp Gauge

Greddy Oil Pressure Gauge

Greddy Water Temp Gauge

Greddy Boost Gauge

 

I've not interested in messing about with Race fuel as theres no point as the stuff is two damn expensive and not practical for road usage... I want to try and keep the existing turbos on...

 

Jurgen will be posting update pics on regular occassions.... I dont want the car with any less than 800bhp for the road.. so wel will see how it gets on :)

Edited by suprafan72 (see edit history)
Link to comment
Share on other sites

  • Replies 552
  • Created
  • Last Reply

Top Posters In This Topic

So what HP is it putting out now?? Does Jurgen still have the car?? If you want 800hp then make sure you/he uses a hub dyno, Im not too familiar with the specs of the turbos on it but I would say looking at the spec 800 would be fairly easy even on pump fuel. What fuel is available where the car will live.

Link to comment
Share on other sites

So what HP is it putting out now?? Does Jurgen still have the car?? If you want 800hp then make sure you/he uses a hub dyno, Im not too familiar with the specs of the turbos on it but I would say looking at the spec 800 would be fairly easy even on pump fuel. What fuel is available where the car will live.

 

 

Its running around 650 at teh moment.... The car will be run in the uk as im back there late spring :)

Link to comment
Share on other sites

FIRST OFF CAR ARRIVED FROM JAPAN..

 

SO CAR GOES ON RAMPS FOR AN INSPECTION AND UNDERSEAL JOB.

 

ONCE ALL THAT WAS DONE WE FITTED SOME FACELIFT REAR LIGHTS..

 

ALONG WITH THE FOLLOWING-

 

FOG TO REAR LIGHT

NCS SPEEDO CHIP

ENGINE OIL CHANGE

NEW PLUGS

 

 

ONCE ALL THIS WAS DONE IT WAS LEFT TO DRY OVERNIGHT SO UNDERSEAL TAKES EFFECT..WE CHARGE £100 INC MATERIALS FOR THIS AND SPEND AROUND 4-5 HOURS..

 

 

image

image

 

image

image

image

 

image

image

 

image

 

image

 

image

 

image

 

image

image

 

 

image

 

image

 

image

 

image

 

image

 

image

 

image

Edited by Jurgen-Jm-Imports (see edit history)
Link to comment
Share on other sites

NEXT JOBS=

 

all interior removed and seats to be retrimmed in leather.

 

rear seats - will not be used (so we might use some of this area for a nice sound sytem compartment..(my friend will do this work).

 

remove headlights and fit 12k hid along with facelift fronts.

 

remove bbs alloys and strip and paint dark gunmetal colour and fit some new toyo 888..

 

:)

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue. You might also be interested in our Guidelines, Privacy Policy and Terms of Use.