Guest danny220 Posted November 29, 2009 Share Posted November 29, 2009 (edited) Hi hello and all that. I have a 93 N/A supra it's had a new clutch (RPS) about a year ago. I've changed the slave cylinder recently but my pedal still sinks to the carpet when I push the pedal in half way and I get a squeaking noise from outside the car when pedal is pushed repeatedly. Any suggestions? Edited November 29, 2009 by danny220 (see edit history) Quote Link to comment Share on other sites More sharing options...
devan Posted November 29, 2009 Share Posted November 29, 2009 Same. Very annoying, tried rubricating various parts, but to no avail. Quote Link to comment Share on other sites More sharing options...
Kirk Posted November 29, 2009 Share Posted November 29, 2009 Sounds possibly like your release bearing is doing the squeaking as for the pedal sinking to the floor id suggest checking your clutch hardline, flexi hose and MC to makesure you have got any leaks Quote Link to comment Share on other sites More sharing options...
trinitom Posted November 29, 2009 Share Posted November 29, 2009 could be a dry gearbox “fork” i had this on my integra, and now on the supra. very annoying! Quote Link to comment Share on other sites More sharing options...
Kirk Posted November 29, 2009 Share Posted November 29, 2009 could be a dry gearbox “fork” i had this on my integra, and now on the supra. very annoying! yes thats a good point, very common for this. Quick spray of grease usualy shuts it up that wouldnt cause the sinking clutch i dont think, almost sounds like the system has air in it kind of like a brake pedal when the lines are air locked Quote Link to comment Share on other sites More sharing options...
martini Posted November 29, 2009 Share Posted November 29, 2009 I also have a squeaky clutch which I would like eventually sorted Quote Link to comment Share on other sites More sharing options...
Kirk Posted November 29, 2009 Share Posted November 29, 2009 yes we know martin! when you can afford it we will Quote Link to comment Share on other sites More sharing options...
Guest danny220 Posted November 29, 2009 Share Posted November 29, 2009 Just does my friggen sweed in. Quote Link to comment Share on other sites More sharing options...
martini Posted November 29, 2009 Share Posted November 29, 2009 yes we know martin! when you can afford it we will Just joining in! Quote Link to comment Share on other sites More sharing options...
Guest danny220 Posted December 6, 2009 Share Posted December 6, 2009 System was bleed again still same problem! can't seem to find any leaks and the fluid levels haven't changed. Might just buy master cylinder and take it from there Quote Link to comment Share on other sites More sharing options...
Rinus Posted December 6, 2009 Share Posted December 6, 2009 If the padel stays at the bottom of the carpet, then I think the problem is in your master-cilinder... Had the same issue and changed everything except for the master, and still had the problem... new master>>no problems anymore Quote Link to comment Share on other sites More sharing options...
Guest danny220 Posted December 7, 2009 Share Posted December 7, 2009 Ok thanks will order one from work on Thursday..... Good old employee discounts I say lol Quote Link to comment Share on other sites More sharing options...
Rob Posted December 7, 2009 Share Posted December 7, 2009 Next time your car is up on jacks/stands, crawl under from the nearside and you will see a small rubber boot where the clutch lever enters the bell housing. It has a little rectangular "portal" in the rubber boot, spray some bike grease in there from time to time to prevent the squeaking. Quote Link to comment Share on other sites More sharing options...
AlanM Posted December 8, 2009 Share Posted December 8, 2009 Ok thanks will order one from work on Thursday..... Good old employee discounts I say lol Speak to CW first. When I had this problem (burying in the carpet) he suggested a smaller bore slave cylinder to cure this. Worth speaking to the man Quote Link to comment Share on other sites More sharing options...
Guest danny220 Posted December 8, 2009 Share Posted December 8, 2009 does anyone know the Blue Print product code for Master Cylinder? Quote Link to comment Share on other sites More sharing options...
Guest danny220 Posted February 3, 2010 Share Posted February 3, 2010 New master cylinder sorted it all Quote Link to comment Share on other sites More sharing options...
martini Posted February 3, 2010 Share Posted February 3, 2010 New master cylinder sorted it all Good to know Quote Link to comment Share on other sites More sharing options...
icemanv6 Posted February 3, 2010 Share Posted February 3, 2010 I had my clutch and release bearing done about 6000km ago, when I push the clutch in after a while it makes a similar sound as to when you pull the bonnet hatch, but not as loud, like a clunking sound, is this similar to what you experienced or not? Anyone else? Quote Link to comment Share on other sites More sharing options...
HadeS Posted February 4, 2010 Share Posted February 4, 2010 I know it might not sound good but as some one said about "fork" I treated mine with DW40 and a bit of oil just when you go through rubber near of gearbox. Got no problem at all and clutch is still good after doing 2000miles Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.