Duffman Posted November 17, 2008 Share Posted November 17, 2008 Going to be fitting cat-back, 1st decat & RR at the weekend...got a few questions. 1. First decat has a bracket welded on for some sort of sensor...best to fit this sensor or fit a plate here? 2. What kind of paste do you use to create a seal between exhaust/cat etc? 3. Is it a simple case of removing the 1st cat by 3 bolts and fitting the decat or is there any gaskets etc between the cat and manifold which have to be removed? 4. Exactly where do I fit RR...between 2nd decat & exhaust? Quote Link to comment Share on other sites More sharing options...
Guest Nizam Posted November 17, 2008 Share Posted November 17, 2008 I think before you fit decat pipe you might need to fit Fuel cut denfender first. Quote Link to comment Share on other sites More sharing options...
Duffman Posted November 17, 2008 Author Share Posted November 17, 2008 I think before you fit decat pipe you might need to fit Fuel cut denfender first. thats under control Quote Link to comment Share on other sites More sharing options...
bigbloodyturbo Posted November 17, 2008 Share Posted November 17, 2008 fit the sensor that comes off your 1st cat into your decat. You wont need a RR if you've still got the 2nd cat. For sealing them your going to change from rings to gaskets so go to a motor factors and try and match something yp, your 1st deact should have come with gaskets anyway. Quote Link to comment Share on other sites More sharing options...
Duffman Posted November 17, 2008 Author Share Posted November 17, 2008 fit the sensor that comes off your 1st cat into your decat. You wont need a RR if you've still got the 2nd cat. For sealing them your going to change from rings to gaskets so go to a motor factors and try and match something yp, your 1st deact should have come with gaskets anyway. yeah it come with all required gaskets so should just be a straight swap over with the sensor from 1st cat to 1st decat>? Quote Link to comment Share on other sites More sharing options...
Duffman Posted November 17, 2008 Author Share Posted November 17, 2008 bump Quote Link to comment Share on other sites More sharing options...
bigbloodyturbo Posted November 17, 2008 Share Posted November 17, 2008 should be, i bought an o2 sensor gasket just incase. If i were you i would also buy a set of downpipe studs from mr.Toyota (think they're 10mm) before i'd start as if you snap one off your going to be right up the creek without a paddle as they say. Quote Link to comment Share on other sites More sharing options...
hoff Posted November 17, 2008 Share Posted November 17, 2008 should be, i bought an o2 sensor gasket just incase. If i were you i would also buy a set of downpipe studs from mr.Toyota (think they're 10mm) before i'd start as if you snap one off your going to be right up the creek without a paddle as they say. Got mine from Paul Whiffin, and a good idea too:) Quote Link to comment Share on other sites More sharing options...
Duffman Posted November 17, 2008 Author Share Posted November 17, 2008 should be, i bought an o2 sensor gasket just incase. If i were you i would also buy a set of downpipe studs from mr.Toyota (think they're 10mm) before i'd start as if you snap one off your going to be right up the creek without a paddle as they say. how much they cost? where u get o2 gasket? Quote Link to comment Share on other sites More sharing options...
bigbloodyturbo Posted November 17, 2008 Share Posted November 17, 2008 how much they cost? where u get o2 gasket? i got mine from fleabay, was only 3or4 quid from what i remember, probably cheaper from Mr.T aswell. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.